F.u.n.k.e. TRT800H-OLED Скачать руководство пользователя

Страница: 22 / 50

TRT800H / P/N 800ATC-H-(2xx)-(2xx)

Operation and Installation

Document-No: 03.2124.010.71e / Revision: 2.10

3.7.2 Pin Assignment

The transponder may only be operated together with an
external memory address adaptor TRT800EMxx

Pin Signal

Remarks

Adaptor

Typ

(4)

TRT800

Adaptor

Typ

(

TRT800

EMSS

Adaptor

Typ

TRT800

EMRS

GND

●

Remote control

(1)

Input

●

EEPROM Signal

TRT800EMxx internal

EEPROM Signal

TRT800EMxx internal

TX RS-232

Serial Output

○

●

SwUB

(1)

Output

○

●

Remote control

(1)

Output

●

+UB power supply

Input

●

GND

●

EEPROM VCC

TRT800EMxx internal

EEPROM GND

TRT800EMxx internal

RX RS-232

Serial Input

○

●

Suppression

Input / Output

○

●

Auto-On

(2)

Input

(2)

●

Fly-GND Switch

(3)

Input

(3)

○

●

● = in the plug and get out ○ = in the plug and not get out

∕ = internal connection to the device

(1)

SWUB
OUT, Interface
Remote control

May only be used for compatible f.u.n.k.e. AVIONICS
devices. Do not connect pins if interface is not used.

(2)

Auto-On

Connect to +UB override front panel on/off button. Leave
unconnected to use front panel on/off button.

(3)

Ground Switch/

FLY-GND

If an external Ground Switch is connected, it must
connect this pin to GND to indicate the on-ground
condition.

Leave open otherwise.

(4)

Adaptors
TRT800EM &
TRT800EMSS

Adaptor version does not provide full interface capability
(see table for details).

Содержание TRT800H-OLED



















































Результаты поиска

Содержание TRT800H-OLED

Отзывы:

Похожие инструкции для TRT800H-OLED

Бренды по названию

Популярные бренды

F.u.n.k.e. TRT800H-OLED, Эксплуатация и установка

Результаты поиска

Содержание TRT800H-OLED

Отзывы:

Похожие инструкции для TRT800H-OLED

Бренды по названию

Популярные бренды