F.u.n.k.e. TRT800H-OLED Скачать руководство пользователя

Страница: 7 / 50

TRT800H / P/N 800ATC-H-(2xx)-(2xx)

Operation and Installation

Document-No: 03.2124.010.71e / Revision: 2.10

1.2 Abbreviations

Abb. Meaning

Explanation

FID

Flight ID

Flight plan number or if not assigned
registration number of aircraft

SPI

Special Position
Identification

Activation on request by controllers
„Squawk Ident“, transmits SPI Pulse
for 18 seconds, which highlights the
respective traffic item on the
controllers radar screen

Aircraft Address

assigned ICAO 24-bit address

Aircraft Category

Defines aircraft type according to
specific categories

Reply Information

Maximum airspeed

1.3 Customer Support

In order to facilitate a rapid handling of return shipments, please follow
the instructions of the input guide „Reshipment RMA“ provided at the

Service

-Area within the f.u.n.k.e. AVIONICS GmbH web portal

www.funkeavionics.de.

Any suggestions for improvement of our manuals are
welcome. Contact: [email protected].

Information on software updates is available at f.u.n.k.e.
AVIONICS GmbH.

Содержание TRT800H-OLED



















































Результаты поиска

Содержание TRT800H-OLED

Отзывы:

Похожие инструкции для TRT800H-OLED

Бренды по названию

Популярные бренды

F.u.n.k.e. TRT800H-OLED, Эксплуатация и установка

Результаты поиска

Содержание TRT800H-OLED

Отзывы:

Похожие инструкции для TRT800H-OLED

Бренды по названию

Популярные бренды