background image

12

Revision Number-001     01-01-2020 - Present                                      

EZG Manufacturing

1-800-417-9272             www.ezgmfg.com

Adjusting the Mast Position to Ensure a Stable Load

Do not tilt forward with a load with the forks elevated except when picking up a load. When stacking a

load, tilt the mast backward just enough to stabilize it.

When working with a maximum capacity load, tilt the mast backward and position the load so the heaviest

part is against the carriage.

Move the forklift with the mast tilted back.

When you are ready to stack the load, tilt the mast forward very slowly, and never travel with the mast

tilted forward.

Adjusting the Fork Positions

Level the forks before lifting a load.

Place the forks as far under the load as possible.

Center the weight of the load between the forks. 

A

djust

 

forks manually or with a fork position

er.

Tilt the mast back to stabilize the load.

Lifting the Load

Ensure there is adequate overhead clearance before lifting the load.

Slowly lift the load and tilt the mast backward slightly to stabilize it.

• Slowly return the lift control to the neutral position.

Lowering the Load

• Ensure the load is secure.

Tilt the mast back carefully to stabilize the load.

Slowly move the forklift away from the stack.

Stop the truck and return the mast to the vertical position before lowering the load.

Lower the load so that the lowest point is 6-8 inches (15-20 cm) from the floor.

START/STOP PROCEDURE

Содержание FHN9















































Отзывы: