EZ Digital DS-1000 Series Скачать руководство пользователя страница 10

Страница: 10 / 67

1-2-1 OPERATING ENVIRONMENT

This instrument will operate to its specifications if the environment is

maintained

within the following conditions

- Indoor use

- Altitude up to 2000m use

- Operating temperature 0

~ 40

- Relative humidity 80%

- Main supply voltage fluctuations not exceed 10% of the nominal voltage.

- After turning on the instrument, please allow a pre-heating period of as long

as some 15 minutes.

This instrument has been qualified to the following EN61010-1 Category :

- Installation (Over-voltage) category 2

- Pollution Degree 2

1-2-2 SAFETY SYMBOLS

Where these symbols or indications appear on the instrument or in this

manual, they have the following meanings.

1-2 NOTES FOR A SAFETY OPERATION

Refer to accompanying documents for Safety-related information.

Wherever the symbol is present, see "NOTES FOR A SAFETY OPERATION"

part in this manual.

Risk of hazard which causes fire or serious damage to the instrument or

other equipment. Do not proceed until its suitable conditions are met.

Risk of hazard which may cause injury to human body or danger to life.

If a WARNING appears on the instrument , and in this manual, do not

proceed until its suitable conditions are understood and met.

Ground

Содержание DS-1000 Series




































































Результаты поиска

Содержание DS-1000 Series

Отзывы:

Бренды по названию

Популярные бренды

EZ Digital DS-1000 Series, Руководство по эксплуатации

Результаты поиска

Содержание DS-1000 Series

Отзывы:

Бренды по названию

Популярные бренды