manualshive.com logo in svg

Extron electronics VNR 100, Руководство пользователя, Страница: 16 / 44

Поделиться
Скачать
Extron electronics VNR 100 Скачать руководство пользователя страница 16

 

VNR 100 • Panels and Cabling

10

Front Panel Features

A

B

C C

D

E FG A

K

J

I

H

Figure 8. 

VNR 100 Front Panel

The front panel has a removable bezel, which can be locked in place to secure the media 
drives. When the bezel is locked in place, the DVD player, USB ports, and serial ports are 
not available for use.

NOTE:

  It is not necessary to access the front panel during normal operation of the 

VNR 100.

A

 

Handles (2)

 — the VNR 100 is mounted on sliding rails in a standard rack. The handles 

allow the unit to be pulled in and out of the rack on the rails. They are also used to 
secure the front panel bezel.

B

 

CD and DVD drive

 — used for system updates or software installation.

C

 

USB ports (2)

 — used to connect a mouse and keyboard for the initial configuration. 

There are a total of four USB inputs: two rear panel and two front panel.

D

 

RS-232 Comm port

 — Insert 9-pin RS-232 cable.

E

 

Status LEDs

 — five LEDs, which provide information about:

Power

2

Network

Activity (2)

Network

Activity (1)

1

Drive

Activity

i

Overtemperature

Figure 9. 

Status LED Icons

The 

Overtemperature

 (

i

) LED flashes yellow when a fan has failed. It lights yellow 

solidly when the internal temperature is too high (the ambient temperature may be too 
high or the flow of air to the fan may be obstructed).

Network Activity (2)

 is not active, so this LED does not light.

The 

Network Activity (1)

 LED flashes green when there is activity on network 1.

The 

Drive Activity

 LED flashes yellow when the hard drive is in use.

The 

Power

 LED lights green when the unit is receiving power.

F

 

Reset button

 — use this button to reboot the VNR 100.

G

 

Power button

 — used to apply or turn off the main power. When the main power is 

turned off, standby power is actively supplied to the recorder.

H

 

OS drive

 — houses the solid state operating system drive (removable).

I

 

Media drive

 — houses the media drive (removable).

J

 

Spare drive bays (2)

 — must not have drives fitted.

ATTENTION:

  Do not remove the OS or Media drive when the VNR 100 is powered on.

ATTENTION:

  Ne retirez pas le driver OS ou multimédia lorsque le VNR 100 est 

branché.

Содержание VNR 100













































Отзывы:

Нет отзывов