background image

 

3

Product Category

Rear Panel Features

NOTES:

• 

The panels in figure 2 are for illustration only and are not to the same scale.

• 

For clarity, the first three rear panels in figure 2 are shown with the USB adapter removed.

• 

The fourth panel (bottom right corner) shows the TLC Pro 526M with the USB adapter (

L

) in place. The alignments of 

the TLC Pro 726M and 1026M with the adapter are very similar.

D

D

C

C

A

A B

B

E

E

J

J

H

H

TLC Pro 526M

I

I

G

G

D

D

F

F

C

C

A

A B

B

E

E

F

F
G

G

H

H

I

I

J

J

K

K

D

D

D

D

D

D

D

D

TLC Pro 726M

C

C

A

A B

B

H

H

H

H

E

E
F

F

G

G

D

D

D

D

K

K

D

D

D

D

I

I J

J

TLC Pro 1026M

L

L

e

TLC Pro 526M with USB Adapter in Place

A

Menu Button

 on next page

B

Reset Button

 on next page

C

Reset LED

 on next page

D

Mounting Slots

 on next page

E

Digital Input Monitoring Port

 on next page

F

LAN/PoE Connector

 on next page

G

USB Port

 on next page

H

Speaker

 on next page

I

Mounting Plate Slot

 on next page

J

Mounting Screw

 on next page

K

Rear Panel Status Lights

 on next page

L

USB Adapter

 on next page

Figure 2. 

TLC Pro 526M Rear Panel with the USB Adapter Removed (top left). 
TLC Pro 726M Rear Panel with the USB Adapter Removed (top right). 
TLC Pro 1026M Rear Panel with the USB Adapter Removed (bottom left). 
TLC Pro 526M Rear Panel with the USB Adapter In Place (bottom right).

figure 2

Содержание TLC Pro 526M Series











Отзывы: