SMP 351 Power Up Procedure
NOTE:
Before powering the SMP 351, ensure that all necessary devices are connected
properly. Devices do not need to be powered.
Connect the power cord to a 100 to 240 VAC supply (see
Power Connection
on
page 13). The unit undergoes self testing during the boot sequence (see figure 12). After
the sequence is complete (and when the device is not being configured or has an active
alarm), the default display cycle is on the LCD display.
EXTRON
ELECTRONICS
2
sec.
EXTRON
SMP 351 FW V1.00
45
sec.
SMP 351
INITIALIZING
LOADING
FIRMWARE
30
sec.
~4
sec.
Power
On
NOTE:
The information shown in the default display cycle differs
depending on the active input and the type of video signal.
Time Record displays only during a recording.
Time Remain displays the remaining time in the event and the
estimated recording time available during an unscheduled
recording.
Default Display Cycle
2
sec.
HH:MM:SS
TIME RECORD
2
sec.
2 sec.
In#1 1024x768@60
In#3 720p@60
2 sec.
ARCHIVE 2.0 MB
1280x720@10 fps
HH:MM:SS
TIME REMAIN
Figure 12.
Boot Sequence and Default Display Cycle
The default display cycle varies depending on the input video signal and output stream
selection. It shows the selected inputs and their resolutions, stream bit rate, and output
resolution. During recording, the current length of the recording and time remaining are
added to the default cycle (see the
NOTE
in figure 11, above).
Front Panel Menu Operation
Configuration and adjustments can be performed using the embedded Web pages
(see
Web-Based User Interface
on page 47), the SIS commands (see
Remote
Communication and Control
on page 156), or using the front panel controls and the
menus displayed on the LCD screen. These menus are used primarily during the initial set
up.
Menu Navigation
Menu display
(
G
)
— Displays the configuration
menus on a16x2 LCD display.
MENU button
(
H
)
— Press
MENU
to activate menus
and cycle through the main menus.
NEXT button
(
H
)
— Press
NEXT
to move between
the submenus of the selected main menu.
ADJUST
(
[
,
{
)
knobs
(
I
)
— In configuration mode,
rotate the left (
[
) control and right (
{
) control to scroll
through submenu options and to make configuration
selections. See the flowcharts in this chapter for details.
USB STORAGE
SMP 351
PRESENTATION CAPTURE RECORDER
([WURQ
CONFIG
ADJUST
AUDIO
CHANNEL A
CHANNEL B
L
R
1 2
3 4 5
LAYOUT
PRESET
SWAP
SWAP
NEXT
MENU
NEXT
MARK
I/O
1
2
3
4
%
% &
&
'
'
(
( )
)
*
*
+
+
,
,
-
-
$
$
Menu
Menu
Menu
Menu
Next
Next
Menu
Next
Menu
Next
PICTURE
CONTROL
PRESETS
H POSITION [A] V
<+0000> <+0000>
CHANNEL SELECT
<A> <ON>
ENCODER RECALL
<N/A>
ENCODER SAVE
<N/A>
Rotate
=
to select a channel.
Rotate
]
to turn the channel
on or off.
Rotate
=
to adjust Horizontal
Position.
Rotate
]
to adjust Vertical
Position.
Rotate either to
select a preset.
Press
0(18
to recall the
selected preset.
Press
1(;7
to continue.
Rotate either to select a
preset to save current
settings to.
Press
0(18
to save the
the new preset.
Press
1(;7
to continue.
SMP 351 • Front Panel Operation
22