Symbol definitions
]
= CR/LF (carriage return/line feed)
}
or ¦ = Carriage return (no line feed, hex
0
D)
• = Space
E
or W = Escape
X(
=
0
=
disabled/unassigned/off/unmuted
1
=enabled/assigned/on/muted
X1)
=
Configuration type
0
= IP Config (ip.cfg)
2
= Box specific parameters (box.cfg)
X1!
= Firmware version number
X1@
= Device name (63 characters, max)
Must comply with internet host name
standards.
X1#
= Day, date, and time
(Day,•MM•DD•YY-HH:MM:SS)
X1$
= Time zone acronym (2 to 6 letters)
X1%
= Greenwich Mean Time (GMT) offset value:
-
12:00
to
14:00
. Represents hours
and minutes (HH:MM) offset from GMT
including the time zone name.
X1^
= IP address in dotted decimal notation
(xxx.xxx.xxx.xxx)
Default IP address:
192.168.254.254
(no padding)
Default gateway IP address:
0.0.0.0
Default DNS server IP address:
0.0.0.0
X1&
= Subnet mask
Default: 255.255.0.0 (no padding)
X1*
= Hardware MAC address
(00-05-A6-NN-NN-NN)
X1(
Time in 10s of milliseconds to wait for
characters coming into a serial port before
terminating (min=
0
, max=
32767
and
default=
10
=
100
ms). The response is
returned with leading zeros.
X2)
Time in
10
s of milliseconds to wait
between characters coming into a
serial port before terminating (min=
0
,
max=
32767
and default=
2
=
20
ms). The
response is returned with leading zeros.
Commands using both
X1&
and
X2)
must have both values =
0
or both set
non-zero.
X2!
Parameter to set either Length of message
to receive or Delimiter value. L=#=byte
count (min=
0
, max=
32767
. default=
0L
=
0
byte count).
D
= decimal value for ASCII character.
(min=
0
, max=
00255
. Default=
00000L
).
Value is placed prior to parameter:
3
byte
length =
3L
and ASCII
0A
delimiter is
10D
.
The parameter is case sensitive, must
use capital
D
or capital
L
. The response is
returned with leading zeros.
X2@
Priority status for receiving timeouts:
0
=use
Send
data string command
parameters (if they exist).
1
=use
Configure
receive timeout
command parameters instead (default=
0
).
X2#
= Verbose mode
0
=clear/none (default for Telnet
connections
1
=verbose mode (default for USB and
RS-232 host control)
2
=tagged responses for queries
3
=verbose mode and tagged responses
for queries
X2%
= RS-232 baud rate (9600 [default], 19200,
38400, 57600, 115200)
X2^
= RS-232 parity: single letter:
O
dd,
E
ven,
N
one (default)
X2&
= RS-232 data bits: 7, 8 (default)
X2*
= RS-232 stop bits: 1 (default), 2
X3#
= Password: maximum length 12
characters. All alpha-numeric characters
permitted except
/
,
\
,
|
,"space", and "
*
".
X4)
= Encode profile
1
=base
2
=main
3=high
X4!
= Output mode
1
=video and audio
2
=video only
X4@
= bit rate control type
0
=VBR
1
=CVBR
2
=CBR
X4#
= Video bit rate (
200
to
10000
)
X4$
= Audio bit rate (
80
,
96
,
128
,
192
,
256
,
320
)
X4%
= GOP length (
1
to
30
)
161
SMP 351 • Remote Communication and Control