Front Panel Menu Diagrams
MENU
NEXT
PRESETS
Rotate either to
select a preset to recall.
Rotate either to select
a preset # to save
current settings to.
Rotate
[
to select an
input.
Rotate
{
to select a preset.
Rotate
[
to select an
input.
Rotate
{
to select a preset.
ARCHIVE ENCODER
RECALL <N/A>
ARCHIVE ENCODER
SAVE <N/A>
IN<1> USER RECAL
<N/A>
IN<1> USER SAVE
<N/A>
MENU
NEXT
PICTURE
CONTROL
Rotate
[
to adjust Brightness.
Rotate
{
to adjust Contrast.
Rotate
[
to adjust Horizontal Size.
Rotate
{
to adjust Vertical Size.
Rotate either to select a
channel.
Rotate
[
to adjust Horizontal Position.
Rotate
{
to adjust Vertical Position.
Rotate
[
to select Color.
Rotate
{
to select Tint.
[A] H POSITION V
+0000 +0000
[A] BRIGHT CONTRAST
<064> <064>
[A] COLOR TINT
<064> <064>
[A] H SIZE V
<640> <480>
CHANNEL SELECT
<A> [ON]
MENU
NEXT
-OR-
RECORD/STREAM
CONFIGURATION
Rotate either to
select encoder type.
Rotate either to
select encoder type.
ENCODER
<ARCHIVE>
ENCODER
<CONFIDENCE>
MENU
NEXT
INPUT
CONFIGURATION
Rotate either to
select the input format.
Rotate
[
to select the horizontal
start pixel.
Rotate
{
to adjust the vertical
start pixel.
Rotate
[
to adjust Horizontal Active pixel
width.
Rotate
{
to adjust Vertical Active pixel height.
Rotate
[
to set an
EDID value for the
active input.
Rotate either to
select input.
Rotate either to
select an aspect ratio for the
selected input.
Rotate either to
select an audio input source
for the selected input.
Rotate either to set the
audio input level from -18
to +24 dB.
Rotate
[
to adjust TTL pixel width.
Rotate
{
to adjust phase.
INPUT SELECT
<1>
INPUT #[3]
<YUVp/HDTV>
(3) TTLPIX PHASE
<XXX> <16>
EDID INPUT #[1]
<720p_60_2ch>
(3) H START V
<128> <128>
(3) H ACTIVE V
<1024> <0768>
ASPECT RATIO IN[1]
<FILL>
IN[1] AUDIO SELECT
<LPCH 2CH>
IN[1] AUDIO LEVEL
<0 dB>
MENU
NEXT
BACKGROUND
RECALL
Rotate either to select.
Press
NEXT
to load
the background file
and exit.
RECALL
<back1080.png>
MENU
NEXT
ADVANCED
CONFIGURATION
Rotate
{
to toggle
Auto Memory
On or Off.
Rotate either to
reboot or reset unit
configurations.
Rotate either to select a
test pattern.
Rotate
[
to select input.
Rotate
{
to toggle on or off.
Rotate either to select a
resolution.
Rotate either to select
the drive restriction.
IN<1> AUTO IMAGE
OFF
TEST PATTERN
<N/A>
RESET
<NONE>
AUTO MEMORY
<ON>
PREVIEW HDMI OUT
<1280X720@60Hz>
RECORD DRIVE LIMITER
<NOT RESTRICTED>
VIEW COMM
SETTINGS
This is set at the factory and
cannot be changed.
(Skipped in “Edit” mode.)
Rotate either to
change baud rate.
Rotate either to toggle
DHCP mode On or Off.
Rotate
[
to select octet field.
Rotate
{
to change address.
“Hidden” Menu*
Press and hold
INPUT 5 + NEXT
for 3 seconds.
Rotate either to change mask.
Rotate
[
to select octet field.
Rotate
{
to change address.
SERIAL PORT
9600 RS232
DHCP MODE
<OFF> On
MAC ADRESS
005A6078CEC
IP ADDR
192.168.254.254
GATEWAY
000.000.000.000
SUBNET
255.255.000.000
EDIT COMM
SETTINGS
MENU
CONF BR 350 kpbs
UNI RTP/UDP
NEXT
STATUS
ALARM STATUS
[NONE, HDCP, VIDEO...]
ARCHIVE
[...FILENAME...]
DRIVE SPACE INT
[FREE/TOTAL][GB]
DRIVE SPACE [USB]
[FREE/TOTAL] [GB]
SELECTED VOLNAME
[FREE/TOTAL][GB]
[ARCH] BR 5000kpbs
MULTI TS/RTP
NOTE:
The Input Configuration submenus are input
specific. Depending on the input type, not all
submenus (shown in gray on subsequent pages)
are available.
NOTE:
See the Record/Stream configuration
diagram on the following page.
SMP 351 • Reference Information
205