Extron electronics IPCP Pro PCS1 Скачать руководство пользователя страница 6

Страница: 6 / 10

IPCP Pro PCS1 • Setup Guide (Continued)

Control, Bidirectional — Serial (COM)

Tx Rx

COM

R/S

IPCP

COM

I/O

NOTE:

If you use cable that

has a drain wire, tie the
drain wire to ground at
both ends.

RS-232-

Controllable

Device

Transmit

Receive

Receive (Rx)

Transmit (Tx)

Ground

Strip wires
3/16" (5 mm) max.

Front Panel

3-pole COM

(RS-232)

Select protocol via software.

COM port default protocol:

• 9600 baud

• 8 data bits • 1 stop bit

• no parity

• no flow control

NOTE:

The 3-pole

COM port
supports software
flow control only.

Serial (COM) Port

Rear Panel

Heat Shrink

To 3-pole
COM port

Heat Shrink

Over Shield Wires

Control, Bidirectional — LAN (Ethernet)

1000

LINK

ACT

RO PCS1

LAN

RJ-45

Connector

Insert Twisted

Pair Wires

Pins:

Rear

Panel

Front Panel

Ethernet

Link
LED

Activity
LED

1000 Mbps

Connection

Network is

active.

Data is being

sent/received.

TCP/IP

Network

LAN (Ethernet)

Default protocol, public ports:

Default login

credentials:

• Username:

admin

• Password:

extron

• IPCP IP address: 192.168.

254.250

• Gateway IP address: 0.0.0.0

• Subnet mask: 255.255.255.0

• DNS address: 127.0.0.1

• DHCP client: off

• Link speed and duplex level: autodetected

• Data rates: 10/100/1000Base-T

The control processor is assigned a unique user hardware ID number (MAC address)
(for example, 00-05-A6-05-1C-A0). You may need this address during control processor
configuration. A label that indicates the MAC address is located on the rear or side panel of the unit.

Control, Unidirectional — IR/Serial

IR/S

S G

IR/S

Rear Panel

Front Panel

To the IR Receiver of a

Projector, Display, or

Source Device

(-)

(+)

(-)

(+)

(-)

Two Single IR Emitters

Ground

IR Output Signal

Unidirectional

IR or RS-232

Output

Ground

To a Projector,

Panel Display, or the

Wired IR Remote or

RS-232 Port of a

Source Device

IR/Serial LED

Lights when signals are

transmitted on the IR/serial port.

IR/Serial Ports

Output options:

• IR (30 kHz to 300 kHz,

with or without carrier signals)

• Unidirectional RS-232

MAC: 00-05-A6-

XX-XX-XX

S/N: ####### E######

00-05-A6-XX-XX-XX

MAC: 00-05-A6-

XX-XX-XX

S/N: ####### E######

MAC
Address

Содержание IPCP Pro PCS1











Результаты поиска

Содержание IPCP Pro PCS1

Отзывы:

Похожие инструкции для IPCP Pro PCS1

Бренды по названию

Популярные бренды

Extron electronics IPCP Pro PCS1, Руководство по установке

Результаты поиска

Содержание IPCP Pro PCS1

Отзывы:

Похожие инструкции для IPCP Pro PCS1

Бренды по названию

Популярные бренды