Extron electronics Extron IPL T S4 Скачать руководство пользователя

Страница: 5 / 79

QS-1

IPL T S Series • Quick Start

Step 1

Turn power off and disconnect the device from

its power source.

Step 2

Mount the IPL T S Series unit:

• on a projector

RTS

CTS

Ceiling

Mounting
Bolt

Projector
Mounting
Bracket

Projector Mount

• under a desk

IPL

T S

100

COM

LIN

ACT

Furniture Mount

• or on a rack

Rack Mount

(2) 4-40 x 3/16" Screws

Use 2 mounting holes on

opposite corners.

1U Rack Shelf

1/4 Rack Width False Front

Face Plate

L T

100

COM

LIN

ACT

CTS

L T

100

COM

LIN

CTS

L T

100

COM

LIN

ACT

CTS

Step 3

Connect a local area network (LAN) cable from a

PC, hub, or router to the IPL T S Series unit.

COM

LAN

00-05-A6-00-30-06

POWER
12V

.5A MAX

COM5

TX RX

COM6

COM3

TX RX

COM4

COM

IPL T S6 Ethernet Control Interface

Step 4

Connect RS-232 cables from the IPL T S Series

unit to the audio video (A/V) devices.

Step 5

Connect power cords and apply power in the

following order:

• output devices (projectors, monitors,

speakers)

• IPL T S Series device
• PC or serial controller
• input devices (DSS, cable boxes, etc.)

Step 6

Configure the IPL T S Series device. See chapter

3 for more information.

Step 7

Test the IPL T S Series device via its default Web

pages. See chapter 4 for more information.

COM

12V

.5A MAX

COM

12V

.5A

MAX

Ethernet

RS-232

Remote User

Control and

Administrator

Monitoring

Extron

IPL T S1

Ethernet Control

Interface

RS-232

Plasma Display

Ethernet

TCP/IP

Network

Extron

IPL T S1

Ethernet Control

Interface

Plasma Display

Typical IPL T S Series configuration

Quick Start — IPL T S Series

Содержание Extron IPL T S4
















































































Результаты поиска

Содержание Extron IPL T S4

Отзывы:

Похожие инструкции для Extron IPL T S4

Бренды по названию

Популярные бренды

Extron electronics Extron IPL T S4, Руководство пользователя

Результаты поиска

Содержание Extron IPL T S4

Отзывы:

Похожие инструкции для Extron IPL T S4

Бренды по названию

Популярные бренды