Extron electronics Extron IPL T S4 Скачать руководство пользователя

Страница: 3 / 79

IPL T S Series

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may

cause undesired operation. The Class A limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may

cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to

cause harmful interference, in which case the user will be required to correct the interference at his own expense.

This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit

to ensure compliance with FCC emissions limits.

Содержание Extron IPL T S4
















































































Результаты поиска

Содержание Extron IPL T S4

Отзывы:

Похожие инструкции для Extron IPL T S4

Бренды по названию

Популярные бренды

Extron electronics Extron IPL T S4, Руководство пользователя

Результаты поиска

Содержание Extron IPL T S4

Отзывы:

Похожие инструкции для Extron IPL T S4

Бренды по названию

Популярные бренды