Extron electronics Extron IPL T S4 Скачать руководство пользователя

Страница: 26 / 79

IPL T S Series • Connection and Configuration

3-2

Connection and Configuration

Connecting the Hardware

To connect the IPL T S interface, connect the input and output devices to the unit.

Use figure 3-1, below, as a guide.

COM 1

LAN

UID# 093012052

WER

12V

.5A MAX

COM 2

Extron

IPL T S2

Ethernet Control

Interface

Ethernet

TCP/IP

Network

Laptop

Serial Cables
to Controlled Devices
(switcher, projector, etc.)

Crossover
Cable

Figure 3-1 — IPL T S interface connections

Ethernet connection

Ethernet connection is used on an ongoing basis to connect the IPL T S unit to a

LAN and to control the switching and display devices attached to the unit. To

connect the unit to a LAN, do the following:

. Plug one end of a CAT 5, straight-through Ethernet cable into the rear panel

Ethernet connector on the IPL T S unit. Refer to figure 2-9 in chapter 2 for RJ-

45 connector wiring information.

. Plug the other end of the Ethernet cable into a network switch or hub

connected to an Ethernet LAN or to the Internet.

From your PC, launch a Web browser and type in the IP address previously

set up on the IPL T S (if this hasnt been set up, refer to “Setting the Internet

Protocol (IP) Address” later in this chapter). This displays the System Status

Web page.

Serial connection

The IPL T S interface can be connected to any A/V device that has a serial control

port.

. Connect one end of a serial cable to the rear panel COM port connector of the

IPL T S unit. As an alternative, use a 3.5 mm, 5-pole captive screw connector

where available.

This captive screw connector must be wired appropriately. See figure 2-10 for

pin assignments, if necessary.

Содержание Extron IPL T S4
















































































Результаты поиска

Содержание Extron IPL T S4

Отзывы:

Похожие инструкции для Extron IPL T S4

Бренды по названию

Популярные бренды

Extron electronics Extron IPL T S4, Руководство пользователя

Результаты поиска

Содержание Extron IPL T S4

Отзывы:

Похожие инструкции для Extron IPL T S4

Бренды по названию

Популярные бренды