Extron electronics Extron IPL T S4 Скачать руководство пользователя

Страница: 27 / 79

3-3

IPL T S Series • Connection and Configuration

COM 3

LAN

UID# 09301205

WER

12V

.5A MAX

COM 2

COM 1

COM 2

Lighting

Control

Ethernet

RS-232

DVD

Laptop

VCR

Remote User
Control and
Administrator
Monitoring

Projector

Extron
MAV 62

Matrix Switcher

TCP/IP

Network

Extron
IPL T S4

Ethernet Control
Interface

Extr

MediaLink Controller

MLC 206

DISPLA

POWE

VOLUME

MAX/

MIN

VCR

DVD

Laptop

Extron
MediaLink or
Other Controller

Figure 3-2 — Typical IPL T S interface operating configuration

. Connect the other end of the serial cable to the display or switching device to

be controlled through the IPL T S.

Setting the Internet Protocol (IP) Address

The IPL T S Series units have a factory default IP address of 192.168.254.254. This

IP address must be changed to an address that will operate on your local network.
There are three ways to change the IP address setting:

  •  Add Device > Auto Config IP option in Global Configurator
  •  IPL T S unit’s embedded Web pages
  •  Address Resolution Protocol (ARP) command
Before you begin:

. Obtain a valid IP address for your IPL T S Series device from your A/V

system’s network administrator.

Write down the unit’s MAC address (a 12-digit number) found on a label on

the rear panel of the unit (ex: 00-05-A6-01-0A-74).

. If the unit is not

at it’s factory default IP address (192.168.254.254), perform a

Mode 4 reset:

a. Hold down the Reset button until the Power LED blinks twice (6

seconds), then release.

b. Press and release the Reset button again within 1 second.

The Power LED blinks quickly four times, confirming the Mode 4 reset,

which returns the unit to its factory default IP address.

Содержание Extron IPL T S4
















































































Результаты поиска

Содержание Extron IPL T S4

Отзывы:

Похожие инструкции для Extron IPL T S4

Бренды по названию

Популярные бренды

Extron electronics Extron IPL T S4, Руководство пользователя

Результаты поиска

Содержание Extron IPL T S4

Отзывы:

Похожие инструкции для Extron IPL T S4

Бренды по названию

Популярные бренды