Extreme Networks Altitude 3550 Скачать руководство пользователя страница 5

Altitude 3550 Access Point Deployment Guide

5

1

About This Guide

Introduction

This guide provides detailed hardware setup and deployment instructions for the Extreme Networks

®

 

Altitude

 3550 (AP3550) model access point. The AP3550 model access point is primarily designed for 

outdoor deployments, thus it has a unique set of installation instructions.

Document Conventions

The following

 

document conventions are used in this document:

NOTE

Indicate tips or special requirements.

CAUTION

Indicates conditions that can cause equipment damage or data loss.

WARNING!

Indicates a condition or procedure that could result in personal injury or equipment damage.

Notational Conventions

The following

 

notational conventions are used in this document:

Italics are used to highlight specific items in the general text, and to identify chapters and sections in 
this and related documents.

Bullets (•) indicate:

action items

lists of alternatives

lists of required steps that are not necessarily sequential

Sequential lists (those describing step-by-step procedures) appear as numbered lists.

Содержание Altitude 3550

































Отзывы: