Extreme Flight YAK-55SP Скачать руководство пользователя | Manualshive

Страница: 11 / 20

background image

11

17.

You will need to trim and sand the bottom of the control horn so that it does not
protrude through the top surface. Scuff the portion of the control horn that will
glue into the slot and insert the horn into the base plate and secure to the aileron
with 30 minute epoxy. Repeat for the other aileron.

18.

Slide the ailerons onto the hinges and into position and secure with thin CA.

«
...
9
10
11
12
13
...
»

Содержание YAK-55SP





















Отзывы:

Нет отзывов

Похожие инструкции для YAK-55SP

Бренд: LGB Страницы: 11

Бренд: Fisher-Price Страницы: 6

WILD WEST EXODUS VENGEANCE OF THE EARPS

Бренд: WARCRADLE STUDIOS Страницы: 5

Бренд: Bachmann Страницы: 12

Бренд: Cytron Technologies Страницы: 116

Бренд: LEGO Страницы: 44

Бренд: Nine Eagles Страницы: 12

Бренд: Mania Страницы: 2

Бренд: Beyblade Страницы: 2

Бренд: Trix Страницы: 20

Бренд: Align Страницы: 32

NexSTAR mini EP RxR

Бренд: Hobbico Страницы: 16

TECH DECK WORLD TOUR I PLANB

Бренд: Spin Master Страницы: 2

Бренд: Jamara Страницы: 20

Lancaster landing flaps

Бренд: Eduard Страницы: 2

RC Creatures Gorilla

Бренд: World Tech Toys Страницы: 4

Бренд: Trix Страницы: 36

Бренд: Fisher-Price Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды