background image

20 

 

26.  

Slide the carbon fiber wing tube into the fuselage and the wings onto the tube.  Secure 

to the fuselage using the 2 3mm bolts and washers inserted through the tabs and into the 
pre-installed blind nuts. 

 

Set-up and flying tips 

The CG range for the 52" Extra EXP starts at the front of the wing tube and 
extends to the rear of the wing tube. There is plenty of room on the battery 
tray to move your battery to achieve this CG location.  Depending on your 
flying style you can adjust the position of the battery to alter the CG to 
accommodate your preferences.  For this type of aircraft where I am going to 
predominantly fly aggressive 3D I typically set the airplane up with a neutral 
CG, meaning that when the aircraft is flown inverted straight and level it 
requires no down elevator to maintain altitude.  If your flying style leans more 
toward precision aerobatics then I recommend setting your CG using the 45 
degree line test.  Fly the aircraft from left to right or right to left, whichever 
direction you are more comfortable with at 3/4 to full throttle.  Pull the 
aircraft to a 45 degree up line and establish this line and immediately roll the 
aircraft inverted.  Establish this line and let go of the elevator stick.  Ideally 
the aircraft will continue to track on that 45 degree line for several hundred 
feet before slowly starting to level off.  Adjust the position of your battery to 
achieve this flight condition.  I also highly recommend taking the time to 
properly set up your rates and exponential settings.  Setting up low rates for 
precision maneuvers and high rates for aggressive aerobatics and (continued) 

Содержание 60 EXTRA 300 EXP






















Отзывы: