background image

 

Page 5 

 

1. PRECAUTIONS AND SAFETY 

 

The  stoves  manufactured  in  our  factory  are 
built  with  the  maximum  dedication  to  the 
individual  components  so  as  to  protect  both 
the  user  and  the  installer  from  accidents. 
Authorized  personnel  are  therefore  advised 
to  pay  special  attention  to  the  electrical 
connections  after  any  servicing  operation  on 
the  product,  especially  with  regard  to  the 
stripped  part  of  the  wires,  which  must  not 
protrude in any way from the terminal block 
to  prevent  possible  contact  with  the  live 
parts of the wire. 
 

Installation  must  be  carried  out  by 
authorized  personnel,  who  must  issue 
the 

purchaser 

declaration 

of 

compliance 

of 

the 

system. 

The 

purchaser  shall  assume  responsibility 
for  the  definitive  installation  and 
consequent  proper  operation  of  the 
product  installed.  Extraflame  S.p.A. 
may  not  be  held  responsible  in  the 
event  of  failure  to  observe  these 
precautions.

 

 
This  instruction  manual  constitutes  an 
integral  part  of  the  product.  It  must  always 
accompany  the  appliance,  also  when  it  is 
transferred  to  another  owner  or  user  or 
moved  to  another  location.  If  the  manual 
gets  damaged  or  lost,  ask  your  local  service 
centre for another copy. 
 
This  stove  must  only  be  used  for  the 
applications  for  which  it  was  expressly 
designed. 
The manufacturer declines any responsibility, 
contractually  or  extra-contractually,  for  any 
damage  caused  to  persons,  animals  or 
property by errors in installation, adjustment, 
and maintenance, or by improper use. 

 

After removing the packaging, check to make 
sure  that  the  contents  are  intact  and 
complete.  
If  this  is  not  the  case,  contact  the  vendor 
from whom the appliance was purchased. 
 
The  electrical  components  of  the  stove  must 
only  be  replaced  by  an  authorized  service 
centre. 
 
General  stove  maintenance  must  be  carried 
out at least once a year, scheduled sufficiently 
in advance with the service centre. 

 
The  following  safety  precautions  must 
be observed: 
 

Do  not  allow  the  stove  to  be  used  by 
unattended children or disabled persons. 
 
Do not touch the stove if you are bare-footed 
or if parts of your body are wet or damp. 
Modifying  the  safety  or  adjustment  devices 
without  the  manufacturer’s  approval  or 
instructions is forbidden. 
 
Never  pull,  detach,  or  twist  the  electrical 
cables  coming  out  of  the  stove,  even  if  it  is 
disconnected from the electrical power. 
 
Do not plug or reduce the size of the air vents 
of the room in which the stove is installed. 
The  air  vents  are  critical  for  correct 
combustion. 
 
Keep the packaging materials out of the reach 
of children and unattended disabled persons. 

 
 
 
 
 
 
 

 

Содержание INSERTO COMFORT MINI













































Отзывы: