background image

UK  |  

9

3112015_EBC22_UK

Warranty

All Exodraft products are covered by a 2-year guarantee as per European consumer rights legislation. For 

some countries an extended period of guarantee may apply depending on either national legislation or 

other clearly stipulated conditions. Customer c

omplaints must be handled by a specialised dealer or who-

lesaler (preferably where the Exodraft product has been bought originally). An updated list of Exodraft 

specialised dealers can be found on our website for the country in question.

Exodraft products must always be installed by properly qualified personnel. Exodraft reserves the right to 

change these guidelines without prior notice. 

The warranty and liability does not cover instances regarding personal injury or damage to property or the 

product that can be ascribed to one or more of the following causes:

•  Failure to follow this installation and operation manual
•  Incorrect installation, start-up, maintenance or servicing
•  Improper repairs
• 

Unauthorised structural modifications made to the product

•  Installation of additional components that have not been tested/approved with the product
•  Any damage resulting from continued use of the product despite an evident defect
•  Failure to use original spareparts and accessories
•  Failure to use the product as intended
• 

Exceeding or failure to meet the limit values in the technical data

• 

Force majeure

Содержание EBC22

















































Отзывы: