background image

Warning

To minimise the risk of fire, electric shock, personal injury 

and/or damage to the product please observe the following:

•  Please always read the manual and only use the product in accordance with the 

 

manufacturer’s instructions. If in doubt, contact one of the Exodraft specialized dealers.

• 

 All installations must be carried out by properly qualifi ed personnel in accordance with 

national legislation and regulations.

• 

This product must be earthed. Get assistance from an qualifi ed electrician when in doubt. 

•  This product must always be disconnected under the installation. 
•   Prior to servicing the product, disconnect the power and ensure that it cannot accidentally 

be reconnected.

• 

 Exodraft always recommends the use of a smoke alarm when a solid fuel open fire is 

installed.

•   If the Exodraft fan system has been designed for solid fuel/multi fuel installations, please 

ensure that the design meets the requirements of BS EN15287-1. If this cannot be achie-

ved, a smoke alarm must be installed in the same room as the heat appliance.

UK

Your energy. 

Optimized.

Symbols

The following symbols may be used in the manual 

to draw attention to danger or risk of personal 

injury or damage to the product.

General prohibition

Failure to observe instructions marked with the prohibited 

symbol may result in extreme danger or serious personal injury.

General warning

Failure to observe instructions marked with a danger symbol 

may result in personal injury and/or damage to the product.

General attention

Marks a dangerous situation that, in the worst-case scenario, 

can cause serious personal injury or significant damage to the product.

Electricity hazard/High Voltage

Marks a situation in which caution is advised due to the risk of high voltage electric 

shock which can cause serious personal injury or significant damage to the product.

Connect an earth terminal to the ground

Failure to observe instructions marked with a danger symbol 

may result in personal injury and/or damage to the product.

Permitted and approved

Permitted and approved method of installation.

Prohibited and not approved 

Prohibited and not approved method of installation.

Содержание EBC22

















































Отзывы: