manualshive.com logo in svg

EXFO bv10, Руководство пользователя, Страница: 80 / 116

Поделиться
Скачать
EXFO bv10 Скачать руководство пользователя страница 80

Test Applications

74

BV10

Smart Loopback Test

Smart Loopback Test 

The Smart Loopback feature loops back the stream of data 
(frames/packets). It retransmits incoming frames/packets after exchanging 
the source and destination addresses as well as ports at multiple layers 
(Ethernet MAC, IP, and UDP/TCP). 

Smart Loopback can be enabled (default) or disabled. Refer to 

smart-loopback enable|disable

 on page 70 for more information. 

Modes 

The Smart Loopback mode limits the address/port swapping to a specific 
layer. The BV10 supports the following Smart Loopback modes:

UDP/TCP (default) – Swap MAC addresses, IP addresses, UDP or TCP 
ports when present and addressed to the unit’s TEST port MAC/IP 
address. In other words, swap from Layer 2 up to Layer 4 when 
present.

IP – Swap MAC addresses, IP addresses when present and addressed 
to the unit’s TEST port MAC/IP address. In other words, swap from 
Layer 2 up to Layer 3 when present.

Ethernet – Swap MAC addresses when addressed to the unit’s TEST 
port MAC address. In other words, swap Layer 2 when present. 

Ethernet All Unicast – Swap MAC addresses when the address is 
unicast, regardless of the unit’s MAC address.

Refer to 

smart-loopback mode ethernet-all-unicast|ethernet|ip|udp-tcp

 on 

page 70 for more information. 

Содержание bv10





















































































































Отзывы:

Нет отзывов