manualshive.com logo in svg

EXFO bv10, Руководство пользователя, Страница: 82 / 116

Поделиться
Скачать
EXFO bv10 Скачать руководство пользователя страница 82

Test Applications

76

BV10

Ping Test

Ping Test 

The Ping test (applicable to the LAN and Test ports) provides the ability to 
generate ICMP Echo Requests and provides statistics on the ICMP Echo 
Replies received in response to the ICMP Echo Request. ICMP Echo Replies 
are expected on the same interface on which the ICMP Echo Requests 
were sent. 

The Ping test is always enabled, even during software upgrades on the Test 
port. 

The following table lists the Ping test parameters and default values where 
applicable.

The Ping test returns the following statistics:

Number of packets transmitted. 

Number of packets received. 

Percentage of packet loss. 

Round-trip time (rtt) in ms (minimum, average, maximum, and 
standard deviation values). 

Refer to 

ping

 on page 53 for more information. 

Parameter

Default Value

Destination IP address
Number of packets or continuous

4

Size in bytes

32

Time-To-Live (TTL)

128

Delay (interval between packets)

1000 ms

Timeout

4000 ms

Содержание bv10





















































































































Отзывы:

Нет отзывов