manualshive.com logo in svg

EXFO bv10, Руководство пользователя, Страница: 96 / 116

Поделиться
Скачать
EXFO bv10 Скачать руководство пользователя страница 96

Warranty

90

BV10

Service and Repairs

Service and Repairs

EXFO commits to providing product service and repair for five years 
following the date of purchase.

To send any equipment for service or repair:
1.

Call one of EXFO’s authorized service centers (see 

EXFO Service 

Centers Worldwide

 on page 91). Support personnel will determine if 

the equipment requires service, repair, or calibration.

2.

If equipment must be returned to EXFO or an authorized service 
center, support personnel will issue a Return Merchandise 
Authorization (RMA) number and provide an address for return.

3.

If possible, back up your data before sending the unit for repair.

4.

Pack the equipment in its original shipping material. Be sure to include 
a statement or report fully detailing the defect and the conditions under 
which it was observed.

5.

Return the equipment, prepaid, to the address given to you by support 
personnel. Be sure to write the RMA number on the shipping slip. 

EXFO 

will refuse and return any package that does not bear an RMA number.

Note:

A test setup fee will apply to any returned unit that, after test, is found to 
meet the applicable specifications.

After repair, the equipment will be returned with a repair report. If the 
equipment is not under warranty, you will be invoiced for the cost 
appearing on this report. EXFO will pay return-to-customer shipping costs 
for equipment under warranty. Shipping insurance is at your expense.

Routine recalibration is not included in any of the warranty plans. Since 
calibrations/verifications are not covered by the basic or extended 
warranties, you may elect to purchase FlexCare Calibration/Verification 
Packages for a definite period of time. Contact an authorized service center 
(see 

EXFO Service Centers Worldwide

 on page 91).

Содержание bv10





















































































































Отзывы:

Нет отзывов