EXFO bv10 Скачать руководство пользователя страница 76

Страница: 76 / 116

CLI Command Reference

BV10

Configuration Commands

Test Application Commands

smart-loopback enable|disable

Description

Enables or disables the Smart Loopback application. Smart Loopback is

enabled by default.
This command acts on the Smart Loopback application only; it is not a

global switch for all test applications. For example, if Smart Loopback is

disabled but TWAMP Light is enabled, TWAMP packets continue to be

reflected.
Refer to

Smart Loopback Test

on page 74 for more information.

Syntax

smart-loopback enable|disable

Example

bv10-100>

smart-loopback disable

smart-loopback mode ethernet-all-unicast|ethernet|ip|udp-tcp

Description

Sets the Smart Loopback feature to one of the following modes:



Ethernet All Unicast



Ethernet



UDP/TCP (default)

Refer to

Smart Loopback Test

on page 74 for more information.

Syntax

smart-loopback mode
ethernet-all-unicast|ethernet|ip|udp-tcp

Example

bv10-100>

smart-loopback mode udp-tcp

bv10-100>

smart-loopback mode ethernet

Содержание bv10





















































































































Результаты поиска

Содержание bv10

Отзывы:

EXFO bv10, Руководство пользователя, Страница: 76 / 116

Результаты поиска

Содержание bv10

Отзывы: