manualshive.com logo in svg

Exalt EX-4.9r, Руководство по установке и настройке, Страница: 29 / 115

Поделиться
Скачать
Exalt EX-4.9r Скачать руководство пользователя страница 29

Exalt Communications, Inc. 

r-series 

Installation and Management Manual 

5000007 (ETSI) 

12 

2007-02-12 (draft) 

 

L

 

= Total transmission system losses of all elements between the radio’s RF 

connector and the antenna’s RF connector (all cables, connectors, 
lightning suppressors), in dB, as specified or measured between 5250 
and 5350 MHz 

For the 5250–5350 MHz band, the maximum EIRP allowed for this device is 30dBm. The 
maximum output power of the radio shall never 13dBm. 

The professional installer is responsible to ensure that RF output power is properly adjusted so 
that it does not exceed the regulatory limit of these conditions. 

Canada Compliance 

The EX-5r Series operates under RSS-210 of Industry Canada regulations. The EX-4.9r 
Seriesoperates under RSS-111 of Industry Canada regulations. Operation is subject to the 
following conditions, unless express permission is granted by Industry Canada to operate in a 
different manner: 

•

 

External amplifiers cannot be used to boost the power or to overcome transmission system 
losses, unless the specific amplifier/cable/antenna combination is expressly authorized by 
Industry Canada. 

•

 

Cross-border transmissions are expressly prohibited, except with written permission from 
both Industry Canada and the governing body of the neighboring country (FCC for USA) 

•

 

Only parabolic dish antennas or directional flat-panel antennas may be used. No other types 
of antennas (omni-directional, yagi, and so on) are authorized. Parabolic dishes of either grid 
or solid type are allowed. Maximum gain of each type of antenna allowed is: 

 

Parabolic dish: 37.5 dBi (6'/1.8m diameter) 

 

Directional flat panel: 28 dBi (~2'/61cm  square) 

A complete list of allowed antennas can be found in Industry Canada (IC), Canada on page v. 

IC (Canada) EIRP 

EX-4.9r Series IC (Canada) EIRP 

 For the EX-4.9i model, within the 4940–4990 MHz band, the maximum EIRP allowed is 
+50dBm. The maximum output power of the radio shall never 24dBm. 

For the EX-4.9i models, the transmit power must be reduced from maximum (+20dBm for 
40MHz BW, +24dBm for 20MHz BW, +22dBm for 10MHz) by 1 dB for every 1dB that the 
antenna gain exceeds 26dBi (including transmission system losses).  

The professional installer is responsible to ensure that RF output power is properly adjusted so 
that it does not exceed the regulatory limit of these conditions. 

EX-5r Series IC (Canada) EIRP 

Within the 5725–5850 MHz band, the maximum EIRP allowed is 61.5dBm. The maximum 
output power of the radio shall never 24dBm. 

Содержание EX-4.9r




















































































































Отзывы:

Нет отзывов