Exabyte VXA-2 AUTOPAK1X7 Скачать руководство пользователя страница 91

Страница: 91 / 104

CTOBER

2002

XABYTE

VXA-2 A

UTO

AK1x7

UTOLOADER

ERFORMANCE

PECIFICATIONS

UTOLOADER

OWER

-O

ELF

-T

EST

IME

Each time the autoloader is powered on, it performs a power-on self-test

(POST). During POST, the autoloader:

Performs self-diagnostics and boots up

Moves the robot to the home position (in front of the tape drive)

Checks for cartridges in each slot

If the cartridges are properly installed, the autoloader is ready for operation. If

any cartridge is not properly installed, the autoloader reports an error and the

robot returns to the home position.

The POST time is measured from the time the autoloader is powered on until

it indicates ready status. The average POST time is 34 seconds.

OVE

OMPLETE

IME

Move complete time is measured from the time the autoloader receives a

move command to the time the autoloader returns status indicating that the

move is complete. During a move, the robot picks a cartridge from a slot or the

tape drive, moves it, and places it into another slot or the tape drive.

The average move complete time for the autoloader is less than 10 seconds.

OBOT

ELIABILITY

The mean cycles between failures (MCBF) for the autoloader’s robot is

500,000 cycles. This value does not include failures attributable to the tape

drive, data cartridge, or the cartridge magazine.

During one full cycle, the robot completes the following actions:

Picks a cartridge from a cartridge slot.

Places the cartridge in the tape drive.

Removes the cartridge from the tape drive.

Replaces the cartridge in the cartridge slot.

Содержание VXA-2 AUTOPAK1X7









































































































Результаты поиска

Содержание VXA-2 AUTOPAK1X7

Отзывы:

Exabyte VXA-2 AUTOPAK1X7, Руководство по эксплуатации продукта, Страница: 91 / 104

Результаты поиска

Содержание VXA-2 AUTOPAK1X7

Отзывы: