20
21
gB
Press Switch
(D)
on the control paneL to the “On”
( I )
position�
CHAngIng LAMPs
If a large amount of the smoke appears grey
or colourless it may be that one or more lamps
have failed�
You can check for lamp failure as follows�
1� Set the switch
(D)
on the control panel to the
position “On”
( I )
and switch
(E)
to fire effect
�
2� Carefully pull out the drawer�
3� Find out which lamp is defective and needs
to be replaced�
4� Set switch
(D)
on the control panel to posi-
tion “OFF”
(0)
and pull the mains plug of the
unit from the outlet�
5� Leave the appliance for 20 minutes to allow
the lamps to cool down before removing
them�
6� remove the water tank
(G)
by lifting upwards
and place in a sink�
7� remove sump
(H)
as explained in the “Clean-
ing” section�
8�
B31
remove the defective lamp, by gen-
tly lifting vertically and disengaging the
pins from the lamp holder� replace with a
dimplex Opti-myst, 12v, 50W, gu5�3 base,
8° beam angle, coloured lamp� (Ordering via
www�dimplex�co�uk at “After Sales Service”
or contact the service address relevant for
your country� details of how to purchase the
lamps are contained there�)
9� Carefully insert the two pins of the new lamp
into the two holes in the lamp holder� Push
firmly in place�
10� replace the Sump and water tank and care-
fully close the drawer�
11� Switch on�
reCyCLIng
For electrical products sold within the euro
pean Community.
At the end of the electrical products
useful life it should not be disposed of
with household waste� Please recycle
where facilities exist� Check with your Local
Authority or retailer for recycling advice in your
country�
disposal of used up batteries
dispose of batteries in the proper manner
according to provincial and local regulations�
Any battery may leak electrolyte if mixed with a
different battery type, if inserted incorrectly, if all
the batteries are not replaced at the same time,
if disposed of in a fire, or if an attempt is made to
charge a battery not intended to be recharged�
AFter sALes servICe
Your product is guaranteed for one year from the
date of purchase� Within this period, we undertake
to repair or exchange this product free of charge
(excluding lamps & subject to availability) provided
it has been installed and operated in accordance
with these instructions� Should you require after
sales service or should you need to purchase any
spares, please contact the retailer from whom the
appliance was purchased or contact the service
number relevant to your country on the warranty
card� Please do not return a faulty product to us
in the first instance as this may result in the loss or
damage and delay in providing you with a satisfac-
tory service�
Please retain your receipt as proof of purchase�
ContACt nuMBer & Address
Contact the service address relevant for your
country (see page 64)�
trouBLesHootIng
symptom
Cause
Abhilfe
the flame effect will
not start�
Mains plug is not plugged in�
Check plug is connected to wall socket
correctly�
Switch
(D)
on the control panel is set
to “On”
( I )
but switch
(E)
is not set to
B18
�
Set switch
(E)
on the control panel to
to switch on the fire effect
B18
�
Low water level
Fill the water tank�
Low voltage connector
(K)
not con-
nected properly
B24
�
Check that the connector
(K)
is inserted
correctly
B24
�
the flame effect is
too low�
the rotary knob
(F)
on the control
panel for the fire effect is set very
low
B18
�
Slowly turn the rotary knob
(F)
on
the control panel toward the right to
increase the flames
B18
�
the water level in the sump
(H)
may
be too high because the drawer was
opened and closed more frequently,
the water tank was removed several
times or the unit was moved�
If water level in the sump is more than
40mm, the sump should be removed
and emptied in the sink�
the 2 metal disks
(n)
on the bottom of
the sump may possibly be dirty
B28
�
Clean Metal discs
(n)
with soft brush
supplied
B28
�
refer to the section “Cleaning / Mainte-
nance” for the step-by-step instructions�
Unpleasant smell
when unit is used�
dirty or stale water�
Clean the unit as explained in the
section Cleaning/Maintenance�
Using unfiltered tap water�
Use only filtered tap water�
the flame effect has
too much smoke�
Flame effect setting is too high�
turn the flame effect Control knob
(F)
anticlockwise to minimum� then turn
slowly toward the right by approx� ¼
turn each� give the flame generator
some time to adjust before increas-
ing�
B18
�
Main lamps are not
working and there are
no flames or smoke�
Follow the instructions in Cleaning /
Maintenance under “Fill the water tank”�
Check the plug is connected to wall
socket correctly�
Switch
(E)
on the control panel is set to
“Standby”
B18
� Press switch
(E)
to
until a single beep for the fire effect can
be heard�
