EWM WEGA 351 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 89

background image

Commissioning

Installation

Item No.: 099-004934-EWM01

51

6.3

Installation

CAUTION

Installation site!

The machine must not be operated in the open air and must only be set up and operated
on a suitable, stable and level base!
• The operator must ensure that the ground is non-slip and level, and provide sufficient

lighting for the place of work.

• Safe operation of the machine must be guaranteed at all times.

6.4

Mains connection

DANGER

Hazard caused by improper mains connection!

An improper mains connection can cause injuries or damage property!
• Only use machine with a plug socket that has a correctly fitted protective conductor.
• If a mains plug must be fitted, this may only be carried out by an electrician in accordance

with the relevant national provisions or regulations (any phase sequence for three-phase
machines)!

• Mains plug, socket and lead must be checked regularly by an electrician!

CAUTION

Operating voltage - mains voltage!

The operating voltage shown on the rating plate must be consistent with the mains
voltage, in order to avoid damage to the machine!
• For mains fuse protection, please refer to the “Technical data” chapter!

• Insert mains plug of the switched-off machine into the appropriate socket.

6.5

Machine cooling

NOTE

In this machine series, the machine and torch cooling are temperature controlled. Fans

and coolant pump are therefore only switched on if required, or during the welding
process.
When the torch trigger is pressed and held down, the fans and the pump always run. If the torch
trigger is not being pressed, the fans and pump only run when the temperature exceeds a set
limit value.

To obtain an optimal duty cycle from the power components, the following precautions should be
observed:

•

Ensure that the working area is adequately ventilated.

•

Do not obstruct the air inlets and outlets of the machine.

•

Do not allow metal parts, dust or other objects to get into the machine.

«
...
49
50
51
52
53
...
»

Содержание WEGA 351


























































































Отзывы:

Нет отзывов

Похожие инструкции для WEGA 351

Бренд: FältCom Страницы: 40

Бренд: Harman Kardon Страницы: 2

JBL BAR 5.0 MULTIBEAM

Бренд: Harman Страницы: 25

Бренд: La Crosse Technology Страницы: 2

Бренд: texet Страницы: 28

APPELLO A105NAX

Бренд: E2S Страницы: 10

KegMaster 4 Series

Бренд: Keg King Страницы: 17

Бренд: ADEMCO Страницы: 40

Бренд: Majorcom: Страницы: 15

MY LIFTER BASIC LIFTER

Бренд: Garage Smart Страницы: 31

Бренд: Westlake Audio Страницы: 21

Бренд: NAPCO Страницы: 16

Point-of-Use Drinking Water System

Бренд: R-Can Страницы: 12

Бренд: Quality Heating Страницы: 15

Бренд: Logic Страницы: 3

Бренд: NABI Страницы: 2

Бренд: Kemppi Страницы: 20

Бренд: Miller Страницы: 136

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды