EWM TETRIX 300 AC/DC COMFORT activArc Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 85

background image

Design and function

Transport and installation

099-000120-EW501

26.07.2011

25

5.2

Transport and installation

WARNING

Risk of accident due to improper transport of machines that may not be lifted!
Do not lift or suspend the machine! The machine can fall down and cause injuries! The
handles and brackets are suitable for transport by hand only!
• The machine may not be lifted by crane or suspended!

CAUTION

Installation site!
The machine must not be operated in the open air and must only be set up and
operated on a suitable, stable and level base!
• The operator must ensure that the ground is non-slip and level, and provide sufficient

lighting for the place of work.

• Safe operation of the machine must be guaranteed at all times.

5.3

Machine cooling

To obtain an optimal duty cycle from the power components, the following precautions should be
observed:

•

Ensure that the working area is adequately ventilated.

•

Do not obstruct the air inlets and outlets of the machine.

•

Do not allow metal parts, dust or other objects to get into the machine.

5.4

Workpiece lead, general

CAUTION

Risk of burns due to incorrect connection of the workpiece lead!
Paint, rust and dirt on the connection restrict the power flow and may lead to stray
welding currents.
Stray welding currents may cause fires and injuries!
•  Clean the connections!
•  Fix the workpiece lead securely!
•  Do not use structural parts of the workpiece as a return lead for the welding current!
•  Take care to ensure faultless power connections!

«
...
23
24
25
26
27
...
»

Содержание TETRIX 300 AC/DC COMFORT activArc






















































































Отзывы:

Нет отзывов

Похожие инструкции для TETRIX 300 AC/DC COMFORT activArc

Бренд: York Страницы: 6

Бренд: Lamperd Страницы: 16

Бренд: JBL Страницы: 6

Feeder/Deliming System EV9797-20

Бренд: Everpure Страницы: 2

Бренд: Linear Страницы: 39

Бренд: The Singing Machine Страницы: 56

Бренд: liquidarc Страницы: 36

Бренд: HySecurity Страницы: 8

Бренд: Vigitron Страницы: 2

Бренд: Telefunken Страницы: 41

Бренд: Car-O-Liner Страницы: 92

Connect Control Box

Бренд: Grainfather Страницы: 9

Бренд: MOSA Weld Страницы: 36

Бренд: Miller Electric Страницы: 31

Бренд: Wolf-Guard Страницы: 11

PCWorks Speaker System

Бренд: Cambridge SoundWorks Страницы: 20

Бренд: Miller Страницы: 56

Бренд: Urrea Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды