EWM TETRIX 300 AC/DC COMFORT activArc Скачать руководство пользователя страница 80

Страница: 80 / 85

Rectifying faults

Machine faults (error messages)

099-000120-EW501

26.07.2011

7.2

Machine faults (error messages)

NOTE

A welding machine error is indicated by the collective fault signal lamp (A1) lighting up
and an error code (see table) being displayed in the machine control display. In the
event of a machine error, the power unit shuts down.

• If multiple errors occur, these are displayed in succession.

• Document machine errors and inform service staff as necessary.

Error message

Possible cause

Remedy

Speedometer error

Check wire guide/tube package

Err 3

Wire feed unit not connected

• Switch off cold wire mode in the device

configuration menu (off status)

• Connect wire feed unit

Temperature error

Allow machine to cool down.

Err 4

Error in emergency stop circuit
(interface for mechanised welding)

• Check the external shut-down equipment
• Check plug-in jumper JP 1 on

PCB T320/1

Err 5

Overvoltage

Err 6

Undervoltage

Switch off the machine and check mains
voltages

Err 7

Coolant error (only if cooling module
connected)

Check coolant level and refill if necessary

Err 8

Gas error

Check gas supply

Err 9

Secondary overvoltage

Err 10

PE error

Switch the machine off and on again.
If the error persists, inform the service dept.

Err 11

FastStop position

Edge "Acknowledge error" signal (0 to 1) via
robot interface (if available)

Err 32

Electronics error (I>0 error)

Err 33

Electronics error (Uactual error)

Err 34

Electronics error (A/D channel error)

Err 35

Electronics error (edge error)

Err 36

Electronics error (S sign)

Switch the machine off and on again.
If the error persists, inform the service dept.

Err 37

Electronics error (temperature error)

Allow machine to cool down.

Err 38

---

Err 39

Electronics error (secondary
overvoltage)

Switch the machine off and on again.
If the error persists, inform the service dept.

Err 51

Error in emergency stop circuit
(interface for mechanised welding)

• Check the external shut-down equipment
• Check plug-in jumper JP 1 on PCB

T320/1

Содержание TETRIX 300 AC/DC COMFORT activArc






















































































Результаты поиска

Содержание TETRIX 300 AC/DC COMFORT activArc

Отзывы:

Похожие инструкции для TETRIX 300 AC/DC COMFORT activArc

Бренды по названию

Популярные бренды

EWM TETRIX 300 AC/DC COMFORT activArc, Руководство по эксплуатации

Результаты поиска

Содержание TETRIX 300 AC/DC COMFORT activArc

Отзывы:

Похожие инструкции для TETRIX 300 AC/DC COMFORT activArc

Бренды по названию

Популярные бренды