EWM Tetrix 200 MV Comfort puls 5P TG Скачать руководство пользователя страница 73

Страница: 73 / 80

Rectifying faults

Error messages (power source)

099-000229-EW501

14.04.2015

7.2

Error messages (power source)

A welding machine error is indicated by the collective fault signal lamp (A1) lighting up and an
error code (see table) being displayed in the machine control display. In the event of a machine
error, the power unit shuts down.

The display of possible error numbers depends on the machine version (interfaces/functions).

• If multiple errors occur, these are displayed in succession.
• Document machine errors and inform service staff as necessary.

Error message

Possible cause

Remedy

Err 3

Speedometer error

Check wire guide/hose package

Wire feeder is not connected

• Switch off cold wire mode in the device

configuration menu (off status)

• Connect the wire feeder

Err 4

Temperature error

Allow the machine to cool down

Error in emergency stop circuit
(interface for automated welding)

• Check the external interrupt equipment
• Check jumper JP 1 on PCB T320/1

Err 5

Overvoltage

Switch off machine and check the mains
voltage

Err 6

Low voltage

Err 7

Coolant error (with connected cooling
unit only)

Check coolant level and refill if necessary

Err 8

Gas error

Check gas supply

Err 9

Secondary overvoltage

Switch machine off and on again,
inform the service department if the error
continues

Err 10

PE error

Err 11

FastStop position

Edge 'Acknowledge error' signal (0 to 1) via
robot interface (if available)

Err 12

VRD error

Switch the machine off and on again.
If the error persists, inform the service dept.

Err 16

Pilot arc current

Check welding torch

Err 17

Cold wire error
Excess current limit of a motor control
card has been triggered
Cold wire error

– a permanent deviation

between wire nominal value and actual
value or a blocked drive has been
detected in the process

Inspect the wire feed system (drives, tube
packages, torch):
• Check cold wire on the torch / work piece

(moved against work piece?)

• Check relation of process wire feed

speed to robot travel speed, and correct
if necessary

• Check wire feed for stiffness with wire

inching function (resolve by checking
wire guides section by section)

Reset error via robot interface (reset error)

Err 18

Plasma gas error
Nominal value significantly different
from actual value -> No plasma gas?

• Check plasma gas supply; use the

plasma gas test function on "cold wire
feed unit" if necessary

• Check guiding / connections of the gas

supply hose for leaks / kinks

• Check that the gas supply lead of the

plasma torch is not blocked

Reset error via robot interface (reset error)

Err 19

Shielding gas
Nominal value significantly different
from actual value -> No shielding gas?

Содержание Tetrix 200 MV Comfort puls 5P TG

















































































Результаты поиска

Содержание Tetrix 200 MV Comfort puls 5P TG

Отзывы:

Похожие инструкции для Tetrix 200 MV Comfort puls 5P TG

Бренды по названию

Популярные бренды

EWM Tetrix 200 MV Comfort puls 5P TG, Руководство по эксплуатации

Результаты поиска

Содержание Tetrix 200 MV Comfort puls 5P TG

Отзывы:

Похожие инструкции для Tetrix 200 MV Comfort puls 5P TG

Бренды по названию

Популярные бренды