EWM Tetrix 200 MV Comfort puls 5P TG Скачать руководство пользователя страница 66

Страница: 66 / 80

Design and function

Machine configuration menu

099-000229-EW501

14.04.2015

Display

Setting/selection

Exit the menu

Exit

Torch configuration menu

Set welding torch functions

Torch mode (factory setting 1)

Up-/Down speed

Increase value

= rapid current change (factory setting 10)

Reduce value

= slow current change

Setting the first increment

Setting: 1 to 20 (factory setting 1)

Machine configuration

Settings for machine functions and parameter display

Welding current display (ignition, secondary, end and hotstart currents)

• Pro = welding current display as a percentage of the main current (factory setting)
• Abs = absolute welding current display

Non-latched operation (C version)

• on = on
• off = off (factory setting)

Power display switching (MMA)

• on = actual value display
• off = setpoint value display (factory setting)

Pulses in the upslope and downslope phases

The function can be switched on or off

TIG antistick

• on = function active (factory setting).
• off = function inactive.

Program 0 block

With machines with key switch (access block), program 0 can be disabled. When the
access block has been enabled, programs 1

–x only can be switched.

off

All programs can be selected (ex works)

Programs 1

–x can be selected (program 0 disabled)

Warnings

Warnings can be issued prior to a machine failure.
off

Warnings disabled (ex works)

Warnings enabled

Machine configuration (part two)

Settings for machine functions and parameter display

Ramp function Remote control RTF 1

The ramp function can be switched on and off

spotMatic

Variation of operation mode spotArc, ignition with workpiece contact
• on = on
• off = off (factory setting)

Setting spot time

• on = Short spot time (5 ms - 999 ms, 1 ms- steps)
• off = long spot time (0,01 s - 20,0 s, 10 ms- steps)

Содержание Tetrix 200 MV Comfort puls 5P TG

















































































Результаты поиска

Содержание Tetrix 200 MV Comfort puls 5P TG

Отзывы:

Похожие инструкции для Tetrix 200 MV Comfort puls 5P TG

Бренды по названию

Популярные бренды

EWM Tetrix 200 MV Comfort puls 5P TG, Руководство по эксплуатации

Результаты поиска

Содержание Tetrix 200 MV Comfort puls 5P TG

Отзывы:

Похожие инструкции для Tetrix 200 MV Comfort puls 5P TG

Бренды по названию

Популярные бренды