EWM Tetrix 200 MV Comfort puls 5P TG Скачать руководство пользователя страница 67

Страница: 67 / 80

Design and function

Machine configuration menu

099-000229-EW501

14.04.2015

Display

Setting/selection

Setting process activation

• on = Separate process activation:

The welding process has to be reactivated for every arc ignition by pressing the torch
trigger.

• off = Permanent process activation:

The welding process is activated by pressing the torch trigger once. The following arc
ignitions are initiated by shortly touching the tungsten electrode against the
workpiece.

Torch cooling mode

•  AUt = automatic operation (ex works)
•  on = permanently switched on
•  off = permanently switched off

Welding torch cooling system pre-flow time

Setting 1

–60 min. (ex works 5)

Time-based power-saving mode

• 5 min.–60 min. = Time to activation of power-saving mode in case of inactivity.
• off = inactivated (ex works 20 min.)

Expert menu

activArc voltage measuring

• on = function on (factory setting)
• off = function off

Error output to automated welding interface, contact SYN_A

off

AC synchronisation or hot wire (factory setting)

FSn

Error signal, negative logic

FSP

Error signal, positive logic

AvC

AVC (Arc voltage control) connection

Gas monitoring

Depending on where the gas sensor is situated, the use of a pilot static tube and the
welding process monitoring phase.
off

Function switched off (ex works)

Monitoring during the welding process. Gas sensor between gas valve and
welding torch. With pilot static tube.

Monitoring prior to the welding process. Gas sensor between gas valve and
welding torch. Without pilot static tube.

Permanent monitoring Gas sensor between gas cylinder and gas valve. With
pilot static tube.

Automation menu

Fast take-over of control voltage (automation)

• on = function on
• off = function off (factory setting)

Orbital welding

• off = off (ex works)
• on = on

Orbital welding

Correction value for orbital current

Service menu

Modifications to the service menu may only be carried out by authorised maintenance
staff!

Содержание Tetrix 200 MV Comfort puls 5P TG

















































































Результаты поиска

Содержание Tetrix 200 MV Comfort puls 5P TG

Отзывы:

Похожие инструкции для Tetrix 200 MV Comfort puls 5P TG

Бренды по названию

Популярные бренды

EWM Tetrix 200 MV Comfort puls 5P TG, Руководство по эксплуатации

Результаты поиска

Содержание Tetrix 200 MV Comfort puls 5P TG

Отзывы:

Похожие инструкции для Tetrix 200 MV Comfort puls 5P TG

Бренды по названию

Популярные бренды