EWM Tetrix 200 MV Comfort puls 5P TG Скачать руководство пользователя страница 24

Страница: 24 / 80

Design and function

Transport and installation

099-000229-EW501

14.04.2015

5.4

Transport and installation

5.4.1

Installation

WARNING

Risk of accident due to improper transport of machines that may not be lifted!
Do not lift or suspend the machine! The machine can fall down and cause injuries! The
handles and brackets are suitable for transport by hand only!

• The machine may not be lifted by crane or suspended!

CAUTION

Installation site!
The machine must not be operated in the open air and must only be set up and
operated on a suitable, stable and level base!

• The operator must ensure that the ground is non-slip and level, and provide sufficient

lighting for the place of work.

• Safe operation of the machine must be guaranteed at all times.

5.4.1.1 Adjusting the length of the carrying strap

To demonstrate adjustment, lengthening the strap is shown in the figure. To shorten, the strap's
loops must be inched in the opposite direction.

Figure 5-1

Содержание Tetrix 200 MV Comfort puls 5P TG

















































































Результаты поиска

Содержание Tetrix 200 MV Comfort puls 5P TG

Отзывы:

Похожие инструкции для Tetrix 200 MV Comfort puls 5P TG

Бренды по названию

Популярные бренды

EWM Tetrix 200 MV Comfort puls 5P TG, Руководство по эксплуатации

Результаты поиска

Содержание Tetrix 200 MV Comfort puls 5P TG

Отзывы:

Похожие инструкции для Tetrix 200 MV Comfort puls 5P TG

Бренды по названию

Популярные бренды