EWM T4.05 Скачать руководство пользователя страница 48

Страница: 48 / 53

Rectifying faults

Warnings

099-00T405-EW501

02.07.2020

Rectifying faults

All products are subject to rigorous production checks and final checks. If, despite this, something fails to

work at any time, please check the product using the following flowchart. If none of the fault rectification

procedures described leads to the correct functioning of the product, please inform your authorised dea-

ler.

6.1 Warnings

Depending on the display options of the machine display, a warning message is displayed as follows:

Display type - machine control

Display

Graphic display

two 7-segment displays

one 7-segment display

The cause of the warning is indicated by a corresponding warning number (see table).

The display of possible warning numbers depends on the machine version (interfaces/functions).

• In case of multiple warnings, these

are displayed in sequence.

• Document machine warning and inform service personnel, if required.

Warning code

Possible cause

Remedy

Machine excess temperature

Allow the machine to cool down

Half-wave failures

Check process parameters

Welding torch cooling warning

Check coolant level and refill if necessary

Gas warning

Check gas supply

See warning number 3

Welding consumable (wire electrode)

fault

Check wire feeding (with machines with filler

wire)

CAN bus failure

Inform service

Protective gas warning

Check gas supply

Plasma gas warning

Check gas supply

Coolant temperature warning

Check coolant level and refill if necessary

Coolant flow warning

Check coolant supply; check coolant level

and, if necessary, fill up

Wire stock warning

Check wire feeding (with machines with filler

wire)

Encoder malfunction, drive

Inform service

Drive is operating under overload con-

ditions

Adjust mechanical load

JOB unknown

Select alternative JOB

The warnings can be reset by pressing a push-button (see table):

Machine control

Smart

Classic

Comfort

Smart 2

Comfort 2

Synergic

Push-button

Содержание T4.05






















































Результаты поиска

Содержание T4.05

Отзывы:

Похожие инструкции для T4.05

Бренды по названию

Популярные бренды

EWM T4.05, Руководство по эксплуатации

Результаты поиска

Содержание T4.05

Отзывы:

Похожие инструкции для T4.05

Бренды по названию

Популярные бренды