EWM T4.05 Скачать руководство пользователя страница 46

Страница: 46 / 53

Functional characteristics

Machine configuration menu

099-00T405-EW501

02.07.2020

Display

Setting/selection

Process activation setting

> see 5.1.4.5 chapter

------- Separate process activation (ex works)

------ Permanent process activation

Torch cooling mode

------- Automatic operation (ex works)

------- Permanently enabled

------- Permanently disabled

Welding torch cooling, post-flow time

Setting 1–60 min. (ex works 5 min.)

Time-based power-saving mode

> see 5.3 chapter

Time to activation of the power-saving mode in case of inactivity.

Setting

= disabled or numerical value 5-60 min..

Operating mode switching via interface for automated welding

------ Non-latched

------- Special non-latched

Re-ignition after arc interruption

> see 5.1.3.3 chapter

------ JOB-dependent time (ex works 5 s).

------ Function disabled or numerical value 0.1–5.0 s.

Expert menu

AC average value controller

------- Function enabled (ex works)

------ Function disabled

Reconditioning pulse (tungsten ball stability)

Cleaning effect of the tungsten ball at the end of welding.

------- Function enabled (ex works)

------ Function disabled

Automatic gas post-flow function

> see 5.1.1.1 chapter

------- Function on

------ Function off (factory setting)

activArc voltage measuring

------- Function enabled (ex works)

------ Function disabled

Error output to interface for automated welding, contact SYN_A

------ AC synchronisation or hot wire (ex works)

------ Error signal, negative logic

------ Error signal, positive logic

------ AVC (Arc voltage control) connection

Gas monitoring

Depending on where the gas sensor is situated, the use of a pilot static tube and the

welding process monitoring phase.

------ Function disabled (ex works).

------ Monitoring during the welding process. Gas sensor between gas valve and

welding torch (with pilot static tube).

------ Monitoring prior to the welding process. Gas sensor between gas valve and

welding torch (without pilot static tube).

------ Permanent monitoring Gas sensor between gas cylinder and gas valve (with

pilot static tube).

AC commutation optimisation

------- Function enabled

------ Function disabled (ex works)

Содержание T4.05






















































Результаты поиска

Содержание T4.05

Отзывы:

Похожие инструкции для T4.05

Бренды по названию

Популярные бренды

EWM T4.05, Руководство по эксплуатации

Результаты поиска

Содержание T4.05

Отзывы:

Похожие инструкции для T4.05

Бренды по названию

Популярные бренды