EWM T4.05 Скачать руководство пользователя страница 43

Страница: 43 / 53

Functional characteristics

Power-saving mode (Standby)

099-00T405-EW501

02.07.2020

Display

Setting/selection

Hotstart current

Hotstart time

5.3 Power-saving mode (Standby)

You can activate the power-saving mode by either pressing the push-button

> see 4 chapter

for a pro-

longed time or by setting a parameter in the machine configuration menu (time-controlled power-saving

mode

)

> see 5.6 chapter

When power-saving mode is activated, the machine displays show the horizontal digit in the

centre of the display only.

Pressing any operating element (e.g. turning a rotary knob) deactivates power-saving mode and the ma-

chine is ready for welding again.

5.4 Access control

The machine control can be locked to secure it against unauthorised or unintentional adjustment. The ac-

cess block has the following effect:
• The parameters and their settings in the machine configuration menu, Expert menu and operation se-

quence can only be viewed but not changed.

• Welding procedure and welding current polarity cannot be changed.
The parameters for setting the access block are configured in the machine configuration

> see 5.6 chapter

Enabling access block

• Assign the access code for the access block: Select parameter

and select a number code (0–

999).

• Enable access block: Set parameter

to access block enabled

The access block activation is indicated by the "Access block active" signal light

> see 4 chapter

Disabling access block

• Enter the access code for the access block: Select parameter

and enter the previously selected

number code (0–999).

• Disable access block: Set parameter

to access block disabled

. The only way to disable the

access block is to enter the selected number code.

5.5 Voltage reducing device

Only machine variants with the (VRD/SVRD/AUS/RU) code are equipped with a voltage reduction device

(VRD). The VRD is used for increased safety, especially in hazardous environments such as shipbuilding,

pipe construction or mining.
A VRD is mandatory in some countries and required by many on-site safety instructions for power

sources.
The VRD

> see 4 chapter

signal light is illuminated when the voltage reduction device is operating without

fault and the output voltage is reduced to a value specified in the relevant standard (see technical data).

Содержание T4.05






















































Результаты поиска

Содержание T4.05

Отзывы:

Похожие инструкции для T4.05

Бренды по названию

Популярные бренды

EWM T4.05, Руководство по эксплуатации

Результаты поиска

Содержание T4.05

Отзывы:

Похожие инструкции для T4.05

Бренды по названию

Популярные бренды