EWM T4.05 Скачать руководство пользователя страница 24

Страница: 24 / 53

Functional characteristics

TIG welding

099-00T405-EW501

02.07.2020

As an example the process is shown with HF ignition. Arc ignition with lift arc is also possible, how-

ever

> see 5.1.3 chapter

Selecting the process activation type for the welding process

> see 5.6 chapter

Up-slope and down-slope times possible for long spot time setting range (0.01–20.0 s) only.



Press and release torch trigger (tap) to activate the welding process.



Touch the torch gas nozzle and tungsten electrode tip carefully against the workpiece.



Incline the welding torch over the torch gas nozzle until there is a gap of approx. 2–3 mm between the

electrode tip and the workpiece. Shielding gas flows during the set gas pre-flow time

. The arc igni-

tes and the previously set ignition current

flows.



The main current phase

ends when the set

spot time elapses.



For long-time spot welding only (parameter

The welding current decreases to the end-crater current

within the set down-slope time



The gas post-flow time

elapses and the welding process ends.

Press and release the torch trigger (tap) to reactivate the welding process (only for separate

process activation). Touching the welding torch with the tungsten electrode tip against the

workpiece again will initiate the next welding processes.

5.1.4.6 Non-latched operation, version C

Figure 5-12

1st cycle

• Press torch trigger 1

, the gas pre-flow time elapses.

• HF ignition pulses jump from the electrode to the workpiece. The arc ignites.
• Welding current flows and immediately assumes the set ignition current

(search arc at minimum

setting). HF switches off.

2nd cycle

• Release torch trigger 1.
• The welding current ramps up to the main current AMP in the selected up-slope time

Pressing torch trigger 1 starts the slope

from main current AMP to secondary current

AMP%. Re-

leasing the torch trigger starts the slope

from the secondary current AMP% and back to the main cur-

rent AMP. This process can be repeated as frequently as required.

The welding process is stopped by interrupting the arc in the secondary current (remove the welding torch

from the workpiece until the arc is extinguished, no re-ignition).
The slope times

and

can be set in the Expert menu

> see 5.1.10 chapter

This operating mode must be enabled (parameter

)

> see 5.6 chapter

Содержание T4.05






















































Результаты поиска

Содержание T4.05

Отзывы:

Похожие инструкции для T4.05

Бренды по названию

Популярные бренды

EWM T4.05, Руководство по эксплуатации

Результаты поиска

Содержание T4.05

Отзывы:

Похожие инструкции для T4.05

Бренды по названию

Популярные бренды