EWM T4.05 Скачать руководство пользователя страница 47

Страница: 47 / 53

Functional characteristics

Machine configuration menu

099-00T405-EW501

02.07.2020

Display

Setting/selection

Minimum current limit (TIG)

> see 5.1.2 chapter

Depending on the set tungsten electrode diameter

------- Function disabled

------- Function enabled (ex works)

Access control – access code

Setting: 000 to 999 (000 ex works)

Access control

> see 5.4 chapter

------- Function enabled

------- Function disabled (ex works)

Automation menu

Fast take-over of control voltage (automation)

------- Function enabled

------- Function disabled (ex works)

Orbital welding

------- Function disabled (ex works)

------- Function enabled

Orbital welding

Correction value for orbital current

Service menu

Any changes to the service menu should be agreed with the authorised service person-

nel.

Reset (to factory setting)

------- Disabled (ex works)

------- Reset the values in the machine configuration menu

------- Complete reset of all values and settings

Resetting is performed when exiting the menu (

Automated/Manual (rC on/off) operating mode

Select machine/function control

------with external control voltages/signals

------with machine control

Software version query (example)

07.= ------ system bus ID

03c0= ---- version number

System bus ID and version number are separated by a dot.

Cable resistance alignment

> see 5.1.11 chapter

Only qualified service personnel may change the parameters!

TIG HF start (soft/hard) switching

------- soft ignition (factory setting).

------- hard ignition.

Ignition pulse limit

Setting 0 ms–15 ms (increments of 1 ms)

PCB state – qualified service personnel only!

for AC welding machines only.

not used

for components for automated welding (RC) only.

Содержание T4.05






















































Результаты поиска

Содержание T4.05

Отзывы:

Похожие инструкции для T4.05

Бренды по названию

Популярные бренды

EWM T4.05, Руководство по эксплуатации

Результаты поиска

Содержание T4.05

Отзывы:

Похожие инструкции для T4.05

Бренды по названию

Популярные бренды