EVO Manufacturing EVO-3010 Скачать руководство пользователя

Страница: 3 / 22

READ BEFORE INSTALL

It is generally a good idea to apply Loctite to all threaded bolts.

ALWAYS wear safety glasses and other approved safety gear when working on a vehicle.

All supplied bolts torqued according to chart at end of instruction.

It is recommended all installation be performed by a trained professional. Some modification may have
to be done.

Test brakes and verify no leakage in lines before driving. Recheck often. Removal or trimming
of factory plastic inner fender liner may be required to clear combinations of larger tire sizes
and wheel back spacings.

Professional alignment is recommended after install.

After alignment is complete and no additional adjustments are to be made to control arms. Torque all

1” Jam Nuts to 250 ft/lbs and all

1/4” Jam Nuts torque to 300 ft/lbs. Regularly check al

l jam nuts and

punch bolts on all control arms for proper torque/tightness. Failure to do so may cause premature
wear of threads on arms.

Parts included: Table below shows black (painted) EVO MFG JLU Long Arm Pro.

Description

Part #

Quantity

EVO JL Fr Lower Long Arm Pair

EVO-12324B

EVO JL Rr Lower Long Arm Pair

EVO-11061B

JL HC Long Arm Hardware

EVO-770076

9/16-

18 Flag Nut Straight Tab 1.5”

EVO-12031

EVO JL Front Upper LA Driver

EVO-11037B

EVO JL Front Upper LA Passenger

EVO-11038B

EVO JL Rear Upper LA Driver

EVO-11035B

EVO JL Rear Upper LA Passenger

EVO-11036B

5/8-

18 Flag Nut Straight Tab 1.5”

EVO-12330

Misalignment Spacer 1” Heim

1/16” Bolt 2.625”

EVO-100563263

EVO JL Fr Driver LA Bracket

EVO-12320

EVO JL Fr Passenger LA Bracket

EVO-12321

EVO JL Rr Driver LA Bracket

EVO-12322

EVO JL Rr Passenger LA Bracket

EVO-12323

EVO JL Rr Axle LA Mount Dr

EVO-12333

EVO JL Rr Axle LA Mount Pass

EVO-12334

Содержание EVO-3010























Результаты поиска

Содержание EVO-3010

Отзывы:

Похожие инструкции для EVO-3010

Бренды по названию

Популярные бренды

EVO Manufacturing EVO-3010, Инструкция по эксплуатации

Результаты поиска

Содержание EVO-3010

Отзывы:

Похожие инструкции для EVO-3010

Бренды по названию

Популярные бренды