EVO Manufacturing EVO-3010 Скачать руководство пользователя | Manualshive

Страница: 18 / 22

background image

18

28.

After paint has dried.  Install all
control arms into their new mounting
locations.  Front upper arms will bend
giving clearance around frame.  Rear
upper arms will bend giving clearance
for tire.

29.

Install all control arms with adjustable
end at axle. All arms zerc fittings and
pinch bolts are recommend be on the
up side during install.

30.

Arms fully threaded in will be just
slightly stretched of factory
placement. Some stretch can be done
by lengthening the arm thread out.

Do not exceed 1” total on all arms.

Cycle suspension to check for any
interferences.

ALL CONTROL ARM STARTING LENGTHS
ARE LISTED ON BEGINNING OF
INSTRUCTIONS.

«
...
16
17
18
19
20
...
»

Содержание EVO-3010























Отзывы:

Нет отзывов

Похожие инструкции для EVO-3010

CSL Elite Racing Wheel

Бренд: FANATEC Страницы: 2

Бренд: FANATEC Страницы: 8

Porsche 911 Turbo S Wheel

Бренд: FANATEC Страницы: 9

Бренд: FANATEC Страницы: 35

ThermoSensor Clamp

Бренд: LaserLiner Страницы: 44

Бренд: XP-PEN Страницы: 3

Бренд: Daewoo Страницы: 68

Бренд: Hyundai Страницы: 437

Бренд: Celestron Страницы: 24

Бренд: Kasanova Страницы: 22

Бренд: Hama Страницы: 14

Бренд: Heath Zenith Страницы: 24

Wireless Charging Station Universal

Бренд: BMW Страницы: 160

Бренд: Ericsson Страницы: 487

Ocean Seven 304Plus

Бренд: idronaut Страницы: 79

Бренд: Olympus Страницы: 42

Бренд: Accessory Power Страницы: 7

Бренд: B-PWR Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды