EVGA Z490 FTW Скачать руководство пользователя страница 20

Страница: 20 / 163

EVGA Z490 FTW (122-CL-E497)

- 20 -

found on a motherboard’s rear I/O hub, but can also be used for the chassis’

front panel USB, auxiliary ports that mount in the card slots, and certain

devices that directly connect to the header. The USB 3.2 Gen2 Header on the

Z490 FTW is a shielded USB 3.2 Gen2 Header and supports up to 10Gb/s

with USB 3.2 Gen2.
This USB 3.2 Gen2 Header has a power limit of 3000ma (3A) @ 5V.

27. USB 3.2 Gen1 Header

The USB 3.2 Gen1 header is used to connect additional USB interface plugs to

the motherboard; these headers are most often used to connect the
motherboard to the chassis to enable the USB 3.2 Gen1 ports on the chassis.

These will function similarly to the USB 3.2 Gen1 ports found on the

motherboard’s

rear I/O hub, but can also be used for

the chassis’

front panel

USB, auxiliary ports that mount in the card slots, and certain devices that

directly connect to the header.
USB 3.2 Gen1 standard is 900ma @ 5V for unpowered devices. If your USB

device requires more power, it is recommended to attach a powered USB Hub.
USB 3.2 Gen2 Type-A (found on the I/O Hub) shares the power limit of USB
3.2 Gen1 at 900ma @ 5V.
Note: USB 3.2 Gen1 is more commonly referred to as USB 3.0.

28. BIOS SafeBoot Button

Pressing this button while the system is running will reboot the motherboard

directly into the BIOS without clearing CMOS. This feature is very useful for

situations where the motherboard is unable to complete boot due to a failed

overclock and the user does not want to erase the previous settings used.

29. BIOS Selector Switch

This switch toggles between physical BIOS chips. This board has 2 BIOS chips

as a permanent fixture. Each chip holds only the settings and profiles that have

been saved to the BIOS chip while active. This allows you to swap between

two physically different BIOS chips. This also makes it substantially easier to

hotflash a BIOS if needed. If instructions are needed for hotflashing a BIOS,

please contact EVGA Customer Service (Page 150 for contact info).

30. Rear Panel Connectors (Figure 2)

This is the section referred to as the I/O Hub. This panel contains the
hardwired USB, Sound, and Ethernet connections. Please see Page 13 for a

component level breakdown.

Содержание Z490 FTW




































































































































































Результаты поиска

Содержание Z490 FTW

Отзывы:

Похожие инструкции для Z490 FTW

Бренды по названию

Популярные бренды

EVGA Z490 FTW, Руководство пользователя

Результаты поиска

Содержание Z490 FTW

Отзывы:

Похожие инструкции для Z490 FTW

Бренды по названию

Популярные бренды