evertz EQT-1616-3G-C Скачать руководство пользователя

Страница: 4 / 102

INFORMATION TO USERS IN EUROPE

NOTE

This equipment with the CE marking complies with both the EMC Directive (89/336/EEC) and the Low

Voltage Directive (73/23/EEC) issued by the Commission of the European Community.

Compliance with these directives implies conformity to the following European standards:

•

EN60065

Product Safety

•

EN55103-1 Electromagnetic Interference Class A (Emission)

•

EN55103-2 Electromagnetic Susceptibility (Immunity)

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

the European Union EMC directive. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be required

to correct the interference at his own expense.

INFORMATION TO USERS IN THE U.S.A.

NOTE

FCC CLASS A DIGITAL DEVICE OR PERIPHERAL

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

WARNING

Changes or modifications not expressly approved by Evertz Microsystems Ltd. could void the user’s

authority to operate the equipment.

Use of unshielded plugs or cables may cause radiation interference. Properly shielded interface cables with

the shield connected to the chassis ground of the device must be used.

Содержание EQT-1616-3G-C







































































































Результаты поиска

Содержание EQT-1616-3G-C

Отзывы:

Похожие инструкции для EQT-1616-3G-C

Бренды по названию

Популярные бренды

evertz EQT-1616-3G-C, Руководство пользователя

Результаты поиска

Содержание EQT-1616-3G-C

Отзывы:

Похожие инструкции для EQT-1616-3G-C

Бренды по названию

Популярные бренды