evertz EQT-1616-3G-C Скачать руководство пользователя

Страница: 37 / 102

EQT-1616-3G-C-C

EQT 12G/3G/HD Router

Page 25

ADDITIONAL FEATURES

5.1. 3G VIDEO BYPASS MODULES (+3GBP2)

The +3GBP2 modules are used to maintain 3G video signal through EQT, non-stop, even with a power

loss. In case power is switched off, the modules automatically replace the current route to a ‘one to one

route’. Once the power is back on, the previous routes are reinstated.

Each module has two HDBNC input connectors and two HDBNC outputs connectors.

5.2. 12G VIDEO MODULES (EQT-MTR-12G-2)

The EQT-MTR-12G-2 are multi-transceiver modules that are used to pass 12G video signals through

EQT. These modules can only function with 12G feature key (

EQT-FK-12G)

installed.

Each module has two HDBNC input connectors and two HDBNC outputs connectors.



NOTE:

+3GBP2 and EQT-MTR-12G-2 modules can be placed in the EQT-1616-

3G-C and used at the same time.

5.3. CLEAN & QUIET SWITCHING (EQT-FK-CS)

The EQT-1616-3G-C is capable of performing clean and quiet switching on all 16 outputs with the

EQT-

FK-12G

feature key installed.

In order to activate this functionality, the router requires to receive bi-level reference (NTSC or PAL).

Also, the signal sources need to be of the same standard and frequency. These sources must lock to the

same reference and be timed to within ±1/2 line with respect to the reference as well. The EQT must be

rebooted after enabling or disabling in order for changes to take effect.

The Clean Switch feature also activate Clean Switch Audio and Gearb

ox.

5.3.1. Clean Switch Audio

The Clean Switch Audio allows independently audio shuffling between 256 channels of embedded/de-

embedded audio and 64 channels of MADI audio (total of 320 channels) – ONLY if ‘Break-Away’ Mode

is set in the Web page (Section 6.5.1) or VistaLINK® (Section 7.4.1).

In contrast, ‘Follow Video’ mode allows only video routes with embedded audio channels. Thus, 16

possible routes at the same time.

As demonstrated in Table 5-1, 16 audio channels are embedded in a single video bus, and each video

signal pass through one of the 16 input/output ports. Additionaly, 64 channels of MADI audio pass through

a single input/output port (labeled AUX).



NOTE:

Clean Switch Audio must be set to ‘Break-Away’, in order to route the

320 audios independently.

Содержание EQT-1616-3G-C







































































































Результаты поиска

Содержание EQT-1616-3G-C

Отзывы:

Похожие инструкции для EQT-1616-3G-C

Бренды по названию

Популярные бренды

evertz EQT-1616-3G-C, Руководство пользователя

Результаты поиска

Содержание EQT-1616-3G-C

Отзывы:

Похожие инструкции для EQT-1616-3G-C

Бренды по названию

Популярные бренды