Everlast Power i-MIG 353DPi, Руководство оператора

Страница: 9 / 47

9
Power i - MIG 353DPi
Main Amp Adjustment Range MIG: 20 - 350 Amps Stick: 10 - 350 Amps
Volt Adjustment Range MIG 14 - 40V (±3V) Volts in standard mode (Volt value becomes Offset/Trim value – 5 to +5 in Synergic Pulse/Double
Pulse Modes)
Wire Feed Speed 60 to 600 IPM (.5 - 15 m/min) Includes “ Wire Jog ” mode for loading or changing wire without having to dispense
and waste gas.
Input Voltage 220 - 240V Single phase (208V permissible) and switchable to 480V 3 phase 50/60 Hz
Welder Type Digitally controlled, IGBT inverter type with Pulse CV GMAW (MIG) and CC Stick functions. Features separate
wire feeder with CV Spool Gun or CV Push - Pull gun capability (Spool/Push - Pull Gun optional).
Wire Roll Size and Diameter .030” - .062” wire diameter assortment. including select U groove (aluminum/bronze) and V groove (steel/stainless)
drive rolls. Other optional sizes and types available. Equipped with 12” diameter roll capacity (30 - 44lb). An 8”
adapter is available for use with 10 - 12 lb. rolls. 4” rolls not supported. (Weights referenced are for commonly
sold packages of steel wire for wire diameter)
MIG Operation and Type Synergic standard MIG and Synergic Pulse/Pulse on Pulse MIG function.
Includes V Groove drive rolls for:
.030” to .062” (.8mm to 1.6mm in diameter for Steel, Stainless Steel use.**
Includes U groove drive rolls for:
.040” to .045” (1.0mm to 1.2mm) for Aluminum, and Bronze (brazing) use. **
Additional Drive Rolls may be ordered direct from Everlast ( 2 pc kit). Size and type stamped on side of the drive
roll next to the related groove for easy identification. Synergic Pulse settings for Mild Steel, Stainless Steel, 40XX
series Aluminum, 50XX series Aluminum, and Bronze wires.
Burn Back Control .01 - .5 seconds, 10 - 25V
Inductance 1 - 10 in whole number increments.
Pulse Frequency Single: Synergically Controlled Double (Pulse on Pulse): .1 to 9.9 Hz
Peak Pulse Amps/Volts Single: Synergically Controlled Voltage/Offset (Trim). Amps adjusted to suit thickness.
Double: Synergically Controlled Voltage/Offset (Trim). Amps adjusted for each half cycle of pulse to create
“ stacking effect ” of weld bead. Range 10 - 350 A; 14 - 40V
Pulse Time On Single: Synergically Controlled Double (Pulse on Pulse): 10 - 90% of Peak Pulse setting
Memory Save and recall up to 10 programs (0 - 9)
MIG Burn Back Duration/Voltage .01 - .5 Seconds 5 - 20V ( - 5 to +5 Volt offset/trim value in Synergic Pulse/Double Pulse)
Hot Start MIG 10 - 350A
End Amps/Volts (Crater Fill) 10 - 350A /14 - 28V ( - 5 to 5 offset)
Torch Trigger Functions/latch 2T, 4T, 4T Special
Stick E6010 Capability No, 6011 only
Power Cable Length 9.5 ft. (3m)
Accessories** FCS - 203 Detachable Wire Feeder, PowerCart 300 welder and cylinder cart, 36 Air - Cooled Series MIG torch 9.5 ft.
(3m), PowerCool 400 Water cooler, Work clamp with cable 9.5 ft. (3m)
300 A Stick Torch, with cable (3m) Floating ball type regulator. (Water - Cooled MIG gun is optional even though
the unit includes cooler. Be sure to order a water cooled MIG gun for heavier use and amperages over 275A)
*See next page for complete electrical and technical data.
**Specifications and packaged accessories subject to change without notice.
General Performance Specifications
Section 1 Introduction and Specifications
WARNING!
• Do not use the welder in damp or wet areas. Perspiration and other forms of water in contact with the body can increase the risk
of electrocution.
•
Do not use the welder in corrosive environments.