Eventide Space страница 40 Скачать руководство пользователя

Страница: 40 / 50

User Guide System Mode

After you’ve selected a Parameter Control Knob, you can set the parameter range that the

MIDI CC will control by setting minimum and maximum parameter values.

When a Parameter Control Knob designator is displayed (KNOB0… KNOB9), pressing the Left

Footswitch will display [MIN VAL]. Turn the associated Parameter Control Knob to set the

minimum value. For example, if KNOB0 was selected, turn the Mix Control Knob to set the

minimum value. The Billboard displays the knob value while you’re turning the selected

parameter knob and times out to display the selected [MIN VAL] when the knob is idle.

Push the Left Footswitch again to set the maximum value for the selected Parameter Control

Knob. The Billboard will display [MAX VAL]. Turn the associated parameter knob to adjust the

maximum value. The Billboard displays the knob value while you’re turning the selected

parameter knob and times out to display the selected [MAX VAL] when the knob is idle.

MIDI CCs send values from 0 to 127. The minimum parameter value will be set when the

MIDI CC sends a 0 and the maximum parameter value will be set when the MIDI CC sends

127. MIDI CC values between 0 and 127 are mapped to the selected parameter range.

The parameters controlled in this mode are system-wide and will apply to all Presets.

Note: You can set the minimum value to be greater than the maximum value. If you do so,

when the MIDI CC sends an increasing value, the parameter value will decrease.

Note: While it is possible to assign more than one external controller to any parameter, doing

so is likely to cause confusion and is not recommended. Keep in mind that, if you have

previously assigned a MIDI CC to a control destination, you may want to clear the assignment

before setting up a new assignment. To clear, select the destination (parameter) and select

the source (MIDI CC) as [---].

To Setup the External Control Source

Press the Right Footswitch to select the external control source field for editing. There are two

ways to select an external control source - Manual Select or Learn Mode.

For Manual Select simply turn the Encoder to choose the MIDI Control Source. The choices

are:

BND – MIDI Pitch Bend

C0 - C99 - MIDI Continuous Controller messages from 0 to 99.

To use the Learn Mode to select the external control source, Press the Right Footswitch again.

“LEARN” is displayed prompting you to send a MIDI message for automatic Control Source

assignment. Press the Right Footswitch again to exit LEARN mode and revert to manual

source selection.

Press the Left and Right Footswitches to toggle between Source and Destination to make as

many assignments as you wish.

The default patch is unassigned [---] for all RCV CTL destinations.

Press the Middle Footswitch once to back-up one level to MIDI menu.

Press the Middle Footswitch twice to go to the top level System menu.

[XMT CC] – Control knobs transmit MIDI Continuous Control

The default patch is as follows:

Содержание Space



















































Результаты поиска

Содержание Space

Отзывы:

Похожие инструкции для Space

Бренды по названию

Популярные бренды

Eventide Space, Руководство пользователя

Результаты поиска

Содержание Space

Отзывы:

Похожие инструкции для Space

Бренды по названию

Популярные бренды