Evco EV3 HP Скачать руководство пользователя страница 47

Страница: 47 / 52

EVCO S.p.A.

EV3 HP & EVD HP | Installer manual ver. 1.2 | Code 1443DHPE124

page 47 of 52

Rated impulse-withstand

voltage

EV3 HP

4 KV.

EVD HP

EV3K01

Over-voltage category

EV3 HP

III.

EVD HP

II.

EV3K01 Not

applicable.

Software class and

structure

EV3 HP

EVD HP

EV3K01

Clock

EV3 HP

On request (with secondary lithium battery).

Battery autonomy in the absence of a power supply: > 6 months at 25°C (77°F).

Battery charging time: 24h (the battery is charged by the power supply of the

device).

Drift:

≤

60s/month at 25°C (77°F).

EVD HP

EV3K01 Not

available.

Analogue inputs

EV3 HP

5 inputs:

4 for NTC probes

- 1 can be set up using the configuration parameter for NTC 4-20mA probes or

transducers

EVD HP

EV3K01 None.

NTC analogue inputs (10 K

Ω

@ 25 °C, 77 °F)

Sensor type:

ß3435.

Measurement field:

from -50 to 150°C (from -58 to 248°F).

Resolution: 0.1°C.

Accuracy:

0.5°C from -20 to 40°C, 1°C from -40 to 120°C, 2°C from -50 to 150°C.

Protection: none.

Analogue inputs 4-20 mA

Input resistance:

≤

200

Ω

Resolution: 0.02mA.

Protection:

none; the maximum current permitted on each input is 25mA.

Digital inputs

EV3 HP

5 volt-free contact inputs.

EVD HP

Содержание EV3 HP





















































Результаты поиска

Содержание EV3 HP

Отзывы:

Похожие инструкции для EV3 HP

Бренды по названию

Популярные бренды

Evco EV3 HP, Руководство по установке

Результаты поиска

Содержание EV3 HP

Отзывы:

Похожие инструкции для EV3 HP

Бренды по названию

Популярные бренды