Eurosystems 2500-5, Перевод оригинальных инструкций пользователя, Страница: 22 / 39

EN
GLISH
9
ASSEMBLY OF THE THROTTLE WIRE WITH B&S ENGINE model B&S 450 Series (Fig. 5)
Position the throttle drive lever
(1) which is placed on the engine all its end ( stop position) following the arrow direction. Take the screw (2) and the corresponding terminal stop
clamp away (4) using the suitable tubular spanner. After the above steps you have to position the throttle lever (5) tightened to the handlebar on stop
position as shown by the arrow. After that connect the terminal end wire (3) into the hole (6) on the engine leverage (1).
Position the wire protective covering (3) on the base of the binding clamp (4) and tighten it with a screw (2).
ASSEMBLY OF THE THROTTLE WIRE WITH ENGINE model B&S 625 Series (Fig. 6)
Position the throttle drive lever (1)
placed on the engine all its way ( stop position) to the arrow direction . Take the screw (2) and the corresponding terminal stop clamp (4) away using
the suitable tubular spanner. After the above steps you have to position the throttle lever (5) tightened on the handlebar on stop position as indicated
by the arrow. After that connect the terminal end wire (3) into the hole (6) on the leverage (1) of the engine.
Position the wire protective covering (3) on the base of the binding clamp (4) and tighten it with a screw (2).
ASSEMBLY OF THE CABLE FOR THE CONTROL BAR DRIVE (Fig. 7)
The cable for the control bar drive (4) is already
connected to the black gear lever for tightening (1) placed under the chassis. Do it first and then switch it into the nib (2) hole welded to the chassis,
then into the slot (A) of the handlebar (3) as indicated by the arrow. When the cable is placed in the handlebar area, make the terminal (5) to pass
into the slot of the red lever (6) then the regulator (7) into the cut hole of the nib (8) . Attention ! the regulator nuts (7) should be both positioned in the
external part of the nib (8) as indicated in the picture.
N.B. = we strongly recommend to perform the a.m. assembly before tightening the cutting bar device set to the machine.
ASSEMBLY OF THE SLIDES TO THE CUTTING BLADE (Fig. 8)
ATTENTION ! Before taking the cutting blade out of the packaging
box , please check the plastic protection to be mounted on the blade. As a precaution always wear sturdy gloves.
Position the two slides (1) under the blade (2) making the respective holes (A = slide holes and B = blade holes) to correspond. Complete the
assembly with the screws (3) washers (4) and nuts (5).
ASSEMBLY OF THE CUTTING BLADE TO THE BAR CONNECTION DEVICE (Fig. 9)
In order to make the cutting blade
assembly easier we can recommend to make such operation on a worktable. Make the pin (1) to pass through the boss (2) you can find already
assembled on the blade (3). The cutting blade (3) is tightened to the bar connection device (4) using four screws (5) and four nuts (6) you can find
into the loose parts bag.
ASSEMBLY OF THE CUTTING BLADE CONNECTION DEVICE TO THE UNIT
The motormower is equipped with a connection
device which allows the operator to get a quick and easy connection of the cutting bar to the machine. Fig. 10) with the engine stopped and the unit
in a horizontal position, insert completely the connection bar pin (1) into the unit housing (2) . Fit the belt (3) on the pulley. (4)
Fig.10 A)
position 1 and 2 : turn the handle (5) until you are able to couple the right side spring (6) to the connection (7) .
Position 2 and 3 : to complete the above coupling , rotate the handle (5) in the opposite direction until you are able to tension the spring (6). Repeat
the same operation with the left side spring as above described in position 1 and 2.
Fig.10 B)
the correct coupling/assembly of the (right/left) springs should be as indicated in the picture.