background image

SigNET 200/300 User Guide  
 

 
4  

 

E-LAB-1543 

1.  Introducing the SigNET 200/300 System 

The SigNET 200/300 system must be installed by a qualified installation engineer. When the installation has been 
completed, the engineer provides users with passwords to set or unset and configure the system as required.  

2. Using the Keypad 

The SigNET Keypad is a wall-mounted programming interface unit that allows users to enter User Programming 
menus (password protected), and to perform operational procedures (arm/disarm) on the system. The Keypad unit 
includes an integral front tamper switch and has a 2 line x 16 character display. Three LEDs provide information on 
AC power, system alerts, and communications status. The Keypad features an easy-to-use navigation key to assist 
in locating required programming options, and has 2 context sensitive soft keys (left and right) for selecting the 
required menu or program setting. 

The SigNET Keypad may be factory fitted with a Portable ACE (PACE) proximity device reader and/or a wireless 
module for the enrolment of wireless sensors.  

Figure 1 – SigNET Keypad 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Table 1 – LED Status Indicators 

LED  

Description 

AC Mains LED 
(green)

 

Indicates presence or failure of the Mains supply 

FLASHING:

 AC Mains fault detected 

STEADY:

 AC Mains OK

 

System Alert  
(yellow)

 

Indicates a system alert 

FLASHING:

 System Alert detected; display indicates the location and nature of the alert. If the 

system is SET, no indication  of system alerts is given. 

OFF:

 No alert detected 

Comms LED 
(red)

 

Indicates status of the E-BUS communications when in FULL ENGINEER programming 

Programming Keys 

1 x multi-functional navigation key 
2 x context sensitive programming 
keys (left and right)  

01 Dec 06 17:00 

AC Mains LED 

System Alert LED 

Comms LED 

Keypad 

12 x alphanumeric 
keys for numeric 
and text data entry

Portable ACE 
Receiver Area 

Licence 
Details 

Installer Contact 

Installer Name 

Installation Date 

Pull-down Information Tab 

The installer contact and licence 
details are located on the pull 
down information tab at the rear 
of the unit 

Содержание SigNET 200
















Отзывы: