EURONORM JI500, Руководство пользователя

Страница: 41 / 101

Hub van Doorneweg 8 • 2171 KZ Sassenheim – NL • T +31(0)252 228850 • F +31(0)252 228235 • E sales@euronorm.nl • I euronormdrives.com 40 41
NEURN030000_220_A NEURN030000_220_A
F7.41 Cooling fan control
0: Fan running only when running
1: Fan always running
0
☆
F7.42 Timing function selection 0: Invalid ; 1: Valid 0
★
F7.43 Timing run time selection
0: F7.44 setting
1: AI1
2: AI2
3: Panel potentiometer Analog input range
corresponds~F7.44
0
★
F7.44 Timing run time 0.0Min~6500.0Min 0.0Min
★
F7.45 Current running reaches the set time. 0.0Min~6500.0Min 0.0Min
★
F7.46 Awakens frequency
dormancy frequency(F7.48)to maximum frequency
(F0.19)
0.00Hz
☆
F7.47 Awakens delay time 0.0s~6500.0s 0.0s ☆
F7.48 Dormancy frequency 0.00Hz~awakens requency(F7.46) 0.00Hz
☆
F7.49 Dormancy delay time 0.0s~6500.0s 0.0s
☆
F7.50 AI1 input voltage protection lower limit 0.00V~F7.51 3.1V
☆
F7.51 AI1 input voltage protection upper limit F7.50~10.00V 6.8V
☆
F7.52 Output phase loss protection factor 0~50% 15%
☆
F7.53 Output phase loss detection time multiple 0.0~50.0 1.2
☆
F7.54 Jog mode setting3
Bits:
0: Forward
1: Reverse
2: Determine the direction from the main termina
Ten bits:
0: Restore to the previous state after jogging
1: Stop running after jogging
Hundred bits:
0: Recover to the previous deceleration time
after jogging
1: Keep the deceleration time the same
after jogging
002
☆
5.1.10 F8 Group - Fault and protection
Code Parameter name Setting range
Factory
setting
Change
F8.00 Overcurrent stall gain 0~100 20
☆
F8.01 Overcurrent stall protection current 100%~200% -
☆
F8.02 Motor overload protection selection 0: Invalid 1: Enable 1
☆
F8.03 Motor overload protection gain 0.20~10.00 1.00
☆
F8.04 Motor overload pre-alarm coefficient 50%~100% 80%
☆
F8.05 Over-voltage stall gain 0~100 0
☆
F8.06
Over-voltage stall protection voltage / energy
consumption brake voltage
120%~150% 130%
☆
F8.07 Input phase loss protection selection
Units digit:Input phase loss protection selection
0: Invalid 1: Enable
Tens digit:contactor actuation protection
0: Invalid 1: Enable
11
☆
F8.08 Output phase loss protection selection
0: Invalid
1: Enable
1
☆
F8.09 Short~ground protection 0: Invalid 1: Valid 1
☆
F8.10 Number of automatic fault reset 0~32767 0
☆
F8.11
Fault DO action selection during automatic
fault reset 0: OFF
1: ON
0
☆
F8.12 Automatic fault reset interval 0.1s~100.0s 1.0s
☆
F8.13 Over-speed detection value 0.0~50.0% (Maximum frequency) 20.0%
☆
F8.14 Over-speed detection time 0.0~60.0s 1.0s
☆
F8.15 Detection value for too large speed deviation 0.0~50.0% (Maximum frequency) 20.0% ☆
F8.16 Detection time for too large speed deviation 0.0~60.0s 5.0s
☆